Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P010014  Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P010012.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P010012

HINT:

When P010014 is stored, the ECM enters fail-safe mode. During fail-safe mode, boost prohibited and the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010014 Mass or Volume Air Flow Sensor "A" Circuit Short to Ground or Open The mass air flow meter voltage is less than 0.2 V for 3 seconds or more (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored SAE Code: P0102

HINT:

When this DTC is output, check the mass air flow in the Data List. Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.

DTC No. Mass Air Flow Sensor Malfunction
P010014 0.0 gm/sec
·

Open in mass air flow meter power source circuit

·

Open in VG circuit

·

Short to ground in VG circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter circuit and stores this DTC.

Example:

When the sensor output voltage remains less than 0.2 V for 3 seconds or more, the ECM stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P010014.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER)
A194097C88
0.281,2.021 0.667,2.281 0.385,0.26 1.333,2.438 1.229,3.073 true 0.177,0.073 0.375,0.25 0.198,0.177 10 false *a 1.156,3.125 1.531,3.344 0.375,0.219 10 false +B 0.385,2.063 0.635,2.26 0.25,0.198 10 false C6
*a Front view of wire harness connector
(to Mass Air Flow Meter)


a.

Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C6-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C6 mass air flow meter connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C6-3 (VG) - C62-92 (VG) Always Below 1 Ω
C6-3 (VG) or C62-92 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Data List / All Data / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

v.

Start the engine.


vi.

Check that the Mass Air Flow Sensor value changes when the engine is raced.

OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG