Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P032515  Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P032511.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P032511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P032515 Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open The knock sensor output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic).
·

Open or short in knock sensor circuit

·

Knock sensor

·

ECM


Comes on DTC stored SAE Code:
P0328

HINT:

When DTC P032515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.


Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P032511

MONITOR DESCRIPTION

If the output voltage transmitted by the knock sensor remains high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, and stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and wait 5 minutes.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P032515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK SENSOR)
A287504C53
0.51,2.292 0.865,2.552 0.354,0.26 0.469,0.729 0.844,0.969 0.375,0.24 10 false *a 0.594,2.333 0.865,2.552 0.271,0.219 10 false E1
*a Front view of wire harness connector
(to Knock Sensor)


a.

Disconnect the knock sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E1-2 - E1-1 Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.INSPECT KNOCK SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
2.INSPECT KNOCK SENSOR
a.

Inspect the knock sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>KNOCK SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the knock sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P032515)

NG

3.CHECK HARNESS AND CONNECTOR (KNOCK SENSOR - ECM)
a.

Disconnect the E1 knock sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E1-2 - C62-124 (KNK1) Always Below 1 Ω
E1-1 - C62-123 (EKNK) Always Below 1 Ω
E1-2 or C62-124 (KNK1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P032515)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P032515)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P032515 is output B




A

B