Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P033525  Crankshaft Position Sensor "A" Signal Shape/Waveform Failure  P03353A  Crankshaft Position Sensor "A" Signal has Too Many Pulses  P033564  Crankshaft Position Sensor "A" Signal Plausibility Failure  


DESCRIPTION

The crankshaft position sensor monitors the stop position and performs start control from the position of the stopped crankshaft. Moreover, the crankshaft position sensor contains a function which detects reverse rotation to correctly detect the stop position when the engine rotates reversely.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P033525 Crankshaft Position Sensor "A" Signal Shape/Waveform Failure The pulse width of the crankshaft position sensor exceeding the threshold is detected during engine speed of 1800 rpm or higher (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft pulley (crankshaft position sensor plate)

·

ECM


Comes on DTC stored SAE Code:
P0336
P03353A Crankshaft Position Sensor "A" Signal has Too Many Pulses An engine reverse signal is detected during engine cranking or normally rotating at 1800 rpm or higher (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft pulley (crankshaft position sensor plate)

·

ECM


Comes on DTC stored SAE Code:
P0336
P033564 Crankshaft Position Sensor "A" Signal Plausibility Failure The input signal voltage of the crankshaft position sensor continues at 5 V for 4 seconds during engine rotation (1 trip detection logic).
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft pulley (crankshaft position sensor plate)

·

ECM


Comes on DTC stored SAE Code:
P0336

MONITOR DESCRIPTION

1.

In case the pulse width of the crankshaft position sensor exceeding the threshold is detected during engine normal rotation at 1800 rpm or higher, P033525 is output.

2.

In case an engine reverse signal is detected during engine cranking or normally rotating at 1800 rpm or higher, P03353A is output.

3.

In case the input signal voltage of the crankshaft position sensor continues at 5 V for 4 seconds during engine rotation, P033564 is output.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Required Sensors/Components (Related) Camshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 20 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P033525, P03353A or P033564.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P033525, P03353A AND/OR P033564)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P033525, P03353A or P033564 and P033515 are output A
DTC P033525, P03353A and/or P033564 are output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)

B

7.REPLACE CRANKSHAFT POSITION SENSOR
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
A384859C01
0.25,2.333 0.75,2.583 0.5,0.25 1.875,2.5 2.458,2.979 true 0.354,2.375 0.813,2.573 0.458,0.198 10 false C29 2.479,2.99 2.792,3.188 0.313,0.198 10 false VC 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Crankshaft Position Sensor)


a.

Disconnect the crankshaft position sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C29-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the C29 crankshaft position sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-1 (NE+) - C62-76 (NE+) Always Below 1 Ω
C29-2 (NE-) - C62-109 (NE-) Always Below 1 Ω
C29-1 (NE+) or C62-76 (NE+) - Body ground and other terminals Always 10 kΩ or higher
C29-2 (NE-) or C62-109 (NE-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
B319222C32
2.208,1.583 2.5,1.844 0.292,0.26 10 false *c 0.531,1.781 0.844,1.979 0.313,0.198 10 false *a 2.698,1.781 3.01,1.979 0.313,0.198 10 false *b
*a OK
*b NG
*c Clearance


a.

Check the crankshaft position sensor installation condition.

OK:

Crankshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

5.INSPECT CRANKSHAFT PULLEY (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)

NG

SECURELY REINSTALL CRANKSHAFT POSITION SENSOR

5.INSPECT CRANKSHAFT PULLEY (TEETH OF CRANKSHAFT POSITION SENSOR PLATE)
a.

Inspect the teeth of the crankshaft position sensor plate.

OK:

Crankshaft position sensor plate does not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

7.REPLACE CRANKSHAFT POSITION SENSOR

NG

6.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the C29 crankshaft position sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C29-3 (VC) - C62-110 (VCNE) Always Below 1 Ω
C29-3 (VC) or C62-110 (VCNE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE CRANKSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P033525, P03353A AND/OR P033564)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P033525, P03353A AND/OR P033564)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

k.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P033525, P03353A or P033564 is output B




A

END

B