Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P044313  Evaporative Emission System Purge Control Valve "A" Circuit Open  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for Purge Control) so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The purge VSV operation duty signal is 5 to 95%.
(b) The target control value and actual control value do not match for 10 seconds or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored SAE Code:
P0443

CONFIRMATION DRIVING PATTERN

A179391E82
0.958,1.573 1.167,1.167 1.167,1.167 1.271,1.167 false 1.521,1.948 1.75,2.125 0.229,0.177 10 false [A] 2.844,1.948 3.073,2.125 0.229,0.177 10 false [B] 3.896,3.01 4.125,3.188 0.229,0.177 10 false [C] 4.573,1.333 4.802,1.51 0.229,0.177 10 false [D] 5.094,3.021 5.323,3.198 0.229,0.177 10 false [E] 0.51,2.073 0.885,2.26 0.375,0.188 10 false Idling 4.229,2.604 5.01,2.917 0.781,0.313 10 false 10 minutes or more 2.594,2.583 3.375,2.896 0.781,0.313 10 false 15 minutes or more 1.292,2.583 2.083,2.75 0.792,0.167 10 false Warming up 1.333,1.073 4.104,1.729 2.771,0.656 10 false Between 40 and 60 km/h (25 and 37 mph) 0.125,0.448 1.073,0.615 0.948,0.167 10 false Vehicle Speed

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


9.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P044313.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



15.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


16.

Enter the following menus: Powertrain / Engine / Trouble Codes [E].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

19.

Input the DTC: P044313.

20.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A384821E08
6.177,4.063 6.635,4.26 0.458,0.198 10 false ECM 5.479,1.021 5.917,1.24 0.438,0.219 10 false C62 5.49,2.771 6.104,2.969 0.615,0.198 10 false A38 5.854,0.906 6.313,1.104 0.458,0.198 10 false PRG 5.854,2.688 6.469,2.885 0.615,0.198 10 false MREL 4.333,1.625 5.115,1.844 0.781,0.219 10 false Purge VSV 0.656,2.99 1.573,3.198 0.917,0.208 10 false Battery 2.177,2.115 3,2.354 0.823,0.24 10 false EFI-MAIN 0.688,1.198 1.854,1.458 1.167,0.26 10 false EFI-MAIN NO. 1 3.375,1.219 4.052,1.458 0.677,0.24 10 false EFI NO. 3 4.333,1.469 5.115,1.688 0.781,0.219 10 false C12 4.104,0.938 4.365,1.208 0.26,0.271 10 false 1 5.125,0.927 5.385,1.198 0.26,0.271 10 false 2 5.542,0.833 5.979,1.052 0.438,0.219 10 false 70 5.531,2.583 5.969,2.802 0.438,0.219 10 false 46 0.531,2.021 1.604,2.24 1.073,0.219 10 false BATT MAIN 2.969,1.708 3.125,1.906 0.156,0.198 10 false 5 1.948,1.698 2.104,1.896 0.156,0.198 10 false 6 2.969,0.958 3.125,1.156 0.156,0.198 10 false 4 1.938,0.948 2.094,1.146 0.156,0.198 10 false 3 1.927,2.656 2.385,2.865 0.458,0.208 10 false 1B 1.938,2.802 3.458,3.146 1.521,0.344 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EVAP PURGE VSV)
A384809C01
0.833,1.833 1.458,1.302 true 2.667,2.729 2.042,2.281 true 0.635,1.729 0.802,1.885 0.167,0.156 10 true *1 2.719,2.625 2.885,2.792 0.167,0.167 10 true *2
*1 Vacuum Hose (charcoal canister side)
*2 Purge VSV


a.

Connect the GTS to the DLC3.


b.

Disconnect the fuel vapor feed hose (charcoal canister side) from the purge VSV.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine / Active Test / Activate the EVAP Purge VSV.

Powertrain > Engine > Active Test
Tester Display
Activate the EVAP Purge VSV
50004 372 1

g.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction to your finger.

OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
A346489C28
0.594,2.073 0.99,2.365 0.396,0.292 0.281,0.25 0.594,0.448 0.313,0.198 10 false *a 0.667,2.125 0.979,2.323 0.313,0.198 10 false C12
*a Front view of wire harness connector
(to Purge VSV)


a.

Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C12-1 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the C12 purge VSV connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester connection Condition Specified condition
C12-2 - C62-70 (PRG) Always Below 1 Ω
C12-2 or C62-70 (PRG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR