Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P052012  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery  P052014  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open  P052024  Engine Oil Pressure Sensor/Switch "A" Signal Stuck High  P05202A  Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range  P052400  Engine Oil Pressure Too Low  


DESCRIPTION

A107720E14
0.135,0.708 1.406,1 1.271,0.292 10 false Voltage (V) 0.344,1.031 0.573,1.24 0.229,0.208 10 false 4.5 0.333,2.156 0.563,2.365 0.229,0.208 10 false 0.5 0.74,2.417 0.854,2.625 0.115,0.208 10 false 0 2.542,2.417 2.948,2.688 0.406,0.271 10 false 1.0 1.198,2.688 2.615,2.927 1.417,0.24 10 false Oil Pressure (MPa)

The oil pump is a variable discharge type. The oil pump maintains the oil pressure in the required for VVT operation at low engine speeds and for lubrication at high engine speeds, and reduces friction to lower excess oil pressure at middle engine speeds. The oil pressure sender gauge assembly detects the engine oil pressure.

The oil pressure sender gauge assembly is a semiconductor type pressure sensor whose characteristic resistance changes when pressure is applied. Through this the engine oil pressure is converted into an output voltage which is then amplified and sent to the ECM as the engine oil pressure signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052012 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery The oil pressure sender gauge assembly output voltage is higher than 4.78 V for 5 seconds or more (1 trip detection logic).
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on DTC stored SAE Code:
P0523
P052014 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open The oil pressure sender gauge assembly output voltage is less than 0.23 V for 5 seconds or more (1 trip detection logic).
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on DTC stored SAE Code:
P0522
P052024 Engine Oil Pressure Sensor/Switch "A" Signal Stuck High The oil pressure sender gauge assembly output voltage is higher than the threshold value (1 trip detection logic).
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on DTC stored SAE Code:
P0521
P05202A Engine Oil Pressure Sensor/Switch "A" Signal Stuck in Range The oil pressure sender gauge assembly output voltage is the same value for a certain period of time (1 trip detection logic).
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on DTC stored SAE Code:
P0521
P052400 Engine Oil Pressure Too Low The oil pressure sender gauge assembly output voltage is at or below the threshold value (1 trip detection logic).
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM

·

Engine oil amount insufficient


Comes on DTC stored SAE Code:
P0524

MONITOR DESCRIPTION

The ECM calculates the engine oil pressure based on the output voltage of the oil pressure sender gauge assembly. If any of the following are detected, the ECM will illuminate the MIL and store a DTC.

·

The output voltage of the oil pressure sender gauge assembly is outside of the specified range.

·

The actual output voltage of the oil pressure sender gauge assembly is different than the estimated output voltage based on the engine speed.

·

The oil pressure sender gauge assembly output voltage does not change for a certain period of time.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A331687E02
0.542,1.021 1.219,1.25 0.677,0.229 10 false 4000 rpm 0.052,2.156 1.24,2.729 1.188,0.573 10 false Ignition Switch ON 0.823,1.865 1.5,2.094 0.677,0.229 10 false Idling 6.281,3.344 6.635,3.625 0.354,0.281 9 false [C] 2.063,2.844 2.917,3.146 0.854,0.302 10 false Warming up 3.073,2.854 3.719,3.135 0.646,0.281 10 false 1 minute 4.031,2.865 4.656,3.198 0.625,0.333 10 false 1 minute 5.042,2.865 5.802,3.24 0.76,0.375 10 false 1 minute 2.281,1.813 2.521,2.031 0.24,0.219 10 false [A] 3.146,1.385 3.385,1.604 0.24,0.219 10 false [B] 4.125,1.354 4.365,1.573 0.24,0.219 10 false [B] 5.146,1.375 5.385,1.594 0.24,0.219 10 false [B]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switches turned off [A].

9.

With the vehicle is stationary, gently depress the accelerator pedal and maintain an engine speed of 4000 rpm for 1 minute, then release the accelerator pedal and return to the engine idling [B].

10.

Repeat step [B] 3 times or more.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P052012, P052014, P052024, P05202A or P052400.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A396029E01
1.438,1.031 1.75,1.229 0.313,0.198 10 false VC 0.375,2.906 0.833,3.104 0.458,0.198 10 false C58 0.344,3.094 2.698,3.573 2.354,0.479 10 false Oil Pressure Sender Gauge Assembly 1.333,1.719 1.792,1.917 0.458,0.198 10 false PEO 1.698,0.948 1.854,1.146 0.156,0.198 10 false 3 1.698,1.646 1.854,1.844 0.156,0.198 10 false 2 1.688,2.417 1.844,2.615 0.156,0.198 10 false 1 1.458,2.49 1.74,2.688 0.281,0.198 10 false E2 5.323,3.125 5.781,3.323 0.458,0.198 10 false C62 5.313,3.302 5.771,3.5 0.458,0.198 10 false ECM 4.313,2.417 4.771,2.615 0.458,0.198 10 false 129 4.365,1.635 4.677,1.833 0.313,0.198 10 false 98 4.302,0.938 4.76,1.135 0.458,0.198 10 false 130 4.594,0.948 5.208,1.146 0.615,0.198 10 false VCPE 4.594,1.646 5.052,1.844 0.458,0.198 10 false PEO 4.594,2.417 5.208,2.615 0.615,0.198 10 false EPEO 5.604,0.677 6.063,0.875 0.458,0.198 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P052012, P052014, P052024, P05202A OR P052400)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P052012, P052014, P052024, P05202A or P052400 is output A
DTC P052012, P052014, P052024, P05202A or P052400 and P15EA12 or P15EA14 are output B




A

2.CHECK ENGINE OIL LEVEL

B

2.CHECK ENGINE OIL LEVEL
a.

Check the engine oil level.


b.

Check the state of the oil level warning light (indicator).

Result:
Result Proceed to
Engine oil level is low and oil level warning light (indicator) is illuminated A
Engine oil level is within the specified range and oil level warning light (indicator) is not illuminated B


HINT:

If the oil level warning light (indicator) is not illuminated even though the engine oil level is below the Low mark, or the oil level warning light (indicator) is illuminated even though the engine oil level is within the specified range, inspect the oil level sensor and related parts.




A

3.INSPECT FOR ENGINE OIL LEAK

B

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
3.INSPECT FOR ENGINE OIL LEAK
a.

Check for engine oil leaks.

OK:

There are no engine oil leaks.


HINT:

If there are engine oil leaks, perform repairs.



Result:
Proceed to
NEXT



NEXT

4.ADD ENGINE OIL
4.ADD ENGINE OIL
a.

Add engine oil.

Click hereGeneral>MAINTENANCE>8NR-FTS OIL AND OIL FILTER>REPLACEMENT

NOTICE:

Do not add engine oil to above the full level mark.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P052012, P052014, P052024, P05202A or P052400 is output B




A

B

6.READ VALUE USING GTS (ENGINE OIL TEMPERATURE SENSOR AND ENGINE OIL PRESSURE)
6.READ VALUE USING GTS (ENGINE OIL TEMPERATURE SENSOR AND ENGINE OIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Engine Oil Temperature Sensor and Engine Oil Pressure.

Powertrain > Engine > Data List
Tester Display
Engine Oil Temperature Sensor
Engine Oil Pressure
50003 372 261,103

e.

With the engine oil temperature at 75 to 85°C (167 to 185°F), read the "Engine Oil Pressure" with the engine speed at 1000 rpm.


f.

Read the oil pressure using an oil pressure gauge.



h.

Start the engine.


i.

With the engine oil temperature at 75 to 85°C (167 to 185°F), read the oil pressure gauge with the engine speed at 1000 rpm.


j.

Compare the Data List value and the oil pressure gauge reading.

OK:

Data List value and gauge reading are within +/-50 kPa of each other



Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SENDER GAUGE ASSEMBLY)

NG

10.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF OIL PRESSURE SENDER GAUGE ASSEMBLY)
A248180C82
0.531,2.063 0.958,2.365 0.427,0.302 1.979,2.354 2.333,2.875 true 0.344,0.688 0.74,0.906 0.396,0.219 10 false *a 0.583,2.135 0.969,2.344 0.385,0.208 10 false C58 2.26,2.927 2.75,3.198 0.49,0.271 10 false VC
*a Front view of wire harness connector
(to Oil Pressure Sender Gauge Assembly)


a.

Disconnect the oil pressure sender gauge assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C58-3 (VC) - Body ground Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
8.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
a.

Disconnect the C58 oil pressure sender gauge assembly connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-2 (PEO) - C62-98 (PEO) Always Below 1 Ω
C58-1 (E2) - C62-129 (EPEO) Always Below 1 Ω
C58-2 (PEO) or C62-98 (PEO) - Body ground and other terminals Always 10 kΩ or higher
C58-1 (E2) or C62-129 (EPEO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
a.

Disconnect the C58 oil pressure sender gauge assembly connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C58-3 (VC) - C62-130 (VCPE) Always Below 1 Ω
C58-3 (VC) or C62-130 (VCPE) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Replace the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P052012, P052014, P052024, P05202A OR P052400)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTC P052012, P052014, P052024, P05202A or P052400 is output B




A

END

B