This DTC is applicable to CVT models only.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070513 | Transmission Range Sensor "A" Circuit Open | All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic). | ·
Open or short in park/neutral position switch circuit ·
Park/neutral position switch ·
ECM |
Comes on | DTC stored | SAE Code:
P0705 |
| P070562 | Transmission Range Sensor "A" Signal Compare Failure | Either of the following condition A or B is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more: (a) Any 2 or more of the following signals are ON simultaneously: ·
P input signal ·
R input signal ·
D input signal (b) Any 2 or more of the following signals are ON simultaneously: ·
N input signal ·
R input signal ·
D input signal (c) Any 2 or more of the following signals are ON simultaneously: ·
NSW input signal ·
R input signal ·
D input signal B. Any of the following conditions is met for 2 seconds or more with the shift lever in M: ·
NSW input signal is ON ·
P input signal is ON ·
N input signal is ON ·
R input signal is ON |
·
Open or short in park/neutral position switch circuit ·
Park/neutral position switch ·
Open or short in transmission control switch circuit ·
Shift lock control unit assembly (Transmission control switch) ·
ECM |
Comes on | DTC stored | SAE Code:
P0705 |
These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D, or M). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store a DTC.
| Required Sensors/Components | Park/Neutral position switch |
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Move the shift lever to R and wait 2 seconds or more.
Move the shift lever to N and wait 2 seconds or more.
Move the shift lever to D and wait 2 seconds or more.
Move the shift lever to M and wait 2 seconds or more.
Move the shift lever to P and wait 2 seconds or more.
Wait 1 minute or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P070513 or P070562.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (P Range), Shift SW Status (R Range), Shift SW Status (N Range), Shift SW Status (S Range) and Shift SW Status (D Range).
| Tester Display |
|---|
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (S Range) |
| Shift SW Status (D Range) |
Read the Data List displayed on the GTS.
| GTS Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Shift SW Status (R Range) | Park/Neutral position switch status:
ON or OFF |
·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect |
| Shift SW Status (P Range) | Park/Neutral position switch status:
ON or OFF |
·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect |
| Shift SW Status (N Range) | Park/Neutral position switch status:
ON or OFF |
·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect |
| Shift SW Status (S Range) | Transmission control switch status:
ON or OFF |
·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Shift SW Status (D Range) | Park/Neutral position switch status:
ON or OFF |
·
ON: Shift lever in D or M ·
OFF: Shift lever not in D or M |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW and Shift SW Status (P, R, N and D Range).
| Tester Display |
|---|
| Neutral Position SW |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
According to the display on the GTS, read the Data List.
| GTS Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Neutral Position SW | P or N | ON |
| Except P or N | OFF | |
| Shift SW Status (P Range) | P | ON |
| Except P | OFF | |
| Shift SW Status (R Range) | R | ON |
| Except R | OFF | |
| Shift SW Status (N Range) | N | ON |
| Except N | OFF | |
| Shift SW Status (D Range) | D or M | ON |
| Except D or M | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (S Range).
| Tester Display |
|---|
| Shift SW Status (S Range) |
Read the Data List displayed on the GTS.
| GTS Display | Shift Lever Position | Specified Condition |
|---|---|---|
| Shift SW Status (S Range) | M, "+" or "-" | ON |
| Except M, "+" or "-" | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS
NG
Inspect the Shift lock control unit assembly (Transmission control switch).
for 2WD: Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>SHIFT LEVER>INSPECTION
for AWD: Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>SHIFT LEVER>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2WD) | B |
| NG (for AWD) | C |
A
B
C
| *a | Front view of wire harness connector
(to Shift lock control unit assembly (Transmission control switch)) |
Disconnect the shift lock control unit assembly (transmission control switch) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F17-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.
Disconnect the A38 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F17-5 (S) - A38-59 (S) | Always | Below 1 Ω |
| F17-5 (S) or A38-59 (S) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch) |
Disconnect the park/neutral position switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C36-1 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch.
for 2WD: Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
for AWD: Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2WD) | B |
| NG (for AWD) | C |
A
B
C
Disconnect the C36 park/neutral position switch connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C36-4 (B) - A38-57 (NSW) | Always | Below 1 Ω |
| C36-7 (DL) - C62-34 (D) | Always | Below 1 Ω |
| C36-8 (NL) - C62-66 (N)*1 | Always | Below 1 Ω |
| C36-8 (NL) - C62-65 (N)*2 | Always | Below 1 Ω |
| C36-2 (RL) - C62-35 (R) | Always | Below 1 Ω |
| C36-3 (PL) - C62-65 (P)*1 | Always | Below 1 Ω |
| C36-3 (PL) - C62-64 (P)*2 | Always | Below 1 Ω |
| C36-4 (B) or A38-57 (NSW) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-7 (DL) or C62-34 (D) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-8 (NL) or C62-66 (N)*1, C62-65 (N)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-2 (RL) or C62-35 (R) - Body ground and other terminals | Always | 10 kΩ or higher |
| C36-3 (PL) or C62-65 (P)*1, C62-64 (P)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
*1: w/ Differential Pressure Sensor
*2: w/o Differential Pressure Sensor
| Proceed to |
|---|
| OK |
| NG |
OK
NG