Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT › 2016.10–2019.09
RM32H0E _52 Drivetrain _059517 AXLE AND DIFFERENTIAL _0291568 REAR AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 2.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

a.
C365603

Disconnect the No. 2 parking brake wire assembly connector.


b.

Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.


c.
C365604

Remove the 2 bolts and separate the rear disc brake caliper assembly from the rear axle carrier sub-assembly.

NOTICE:

Use wire or an equivalent tool to keep the rear disc brake caliper assembly from hanging by the rear flexible hose.



Hide 42431 3.REMOVE REAR DISC

Hide 42312E 4.REMOVE REAR AXLE HUB BOLT

a.
C345044C02
0.677,1.354 0.677,1.135 0.677,1.135 1.125,1.135 true 1.531,1.906 1.531,1.417 1.531,1.417 1.406,1.417 true 1.719,0.802 1.719,0.615 1.719,0.615 1.833,0.615 true 0.615,1.354 0.885,1.542 0.271,0.188 10 true *a 1.448,1.927 1.719,2.115 0.271,0.188 10 true *a 1.865,0.531 2.208,0.74 0.344,0.208 10 true SST
*a Service Nut


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, remove the rear axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 5.INSTALL REAR AXLE HUB BOLT

a.
C345045C03
2.885,1.323 2.885,0.896 true 2.531,0.438 2.188,0.438 true 1.115,1.146 0.771,1.146 true 1.5,1.969 1.5,1.417 1.5,1.417 1.375,1.417 true 1.938,0.344 2.188,0.542 0.25,0.198 10 true *a 2.813,1.344 3.125,1.5 0.313,0.156 10 false *b 0.479,1.052 0.729,1.25 0.25,0.198 10 true *a 1.406,2.01 1.656,2.177 0.25,0.167 10 true *a
*a Service Nut
*b Washer


Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.

Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431 6.INSTALL REAR DISC

Hide 7.INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

a.

Install the rear disc brake caliper assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


b.

Install the rear flexible hose to the rear flexible hose bracket with the bolt.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


c.

Connect the No. 2 parking brake wire assembly connector.


Hide 8.INSTALL REAR WHEEL