Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0292315 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  


DESCRIPTION

The VVT (Variable Valve Timing) system adjusts the intake valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.

The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.

A393103E07
2.552,4.563 2.792,4.281 2.792,4.281 3.594,4.281 false 3.156,4.802 3.333,5.104 3.333,5.104 3.896,5.104 false 0.156,0.156 1.052,0.375 0.896,0.219 10 false VVT System: 0.271,2.698 0.99,2.906 0.719,0.208 10 false Duty-cycle 1.573,3.75 4.344,3.969 2.771,0.219 10 false Camshaft Timing Oil Control Valve Assembly 0.333,4.24 1.604,4.469 1.271,0.229 10 false Engine Oil Pressure 3.677,4.177 6.75,4.417 3.073,0.24 10 false VVT Controller (Camshaft Timing Gear Assembly) 3.979,4.99 5.021,5.188 1.042,0.198 10 false Intake Camshaft 2.354,1.281 3.635,1.49 1.281,0.208 10 false Actual Valve Timing 2.333,2.01 3.656,2.24 1.323,0.229 10 false Target Valve Timing 2.635,2.719 3.313,2.917 0.677,0.198 10 false Correction 2.802,3.177 3.188,3.365 0.385,0.188 10 false ECM 4.771,0.833 6.427,1.021 1.656,0.188 10 false Camshaft Position Sensor 4.75,1.344 6.479,1.531 1.729,0.188 10 false Crankshaft Position Sensor 4.958,1.844 6.281,2.052 1.323,0.208 10 false Mass Air Flow Meter 4.854,2.354 6.385,2.573 1.531,0.219 10 false Throttle Position Sensor 4.49,2.865 6.719,3.073 2.229,0.208 10 false Engine Coolant Temperature Sensor 4.906,3.375 6.323,3.594 1.417,0.219 10 false Vehicle Speed Sensor

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0010 Camshaft Position "A" Actuator Circuit (Bank 1) Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve assembly (for intake camshaft) circuit

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC is designed to detect an open or short in the camshaft timing oil control valve assembly (for intake camshaft) circuit. If the camshaft timing oil control valve duty-cycle is excessively high or low while the ignition switch is ON or the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure)

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0010.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A395472E01
1.573,0.583 1.729,0.781 0.156,0.198 10 false 1 1.594,1.219 1.75,1.417 0.156,0.198 10 false 2 4.906,0.573 5.146,0.823 0.24,0.25 10 false 35 4.906,1.208 5.146,1.458 0.24,0.25 10 false 34 5.125,0.563 5.531,0.813 0.406,0.25 10 false OC1+ 5.135,1.198 5.542,1.448 0.406,0.25 10 false OC1- 5.573,1.969 5.979,2.219 0.406,0.25 10 false C63 5.552,2.146 5.958,2.396 0.406,0.25 10 false ECM 0.094,1.594 0.5,1.844 0.406,0.25 10 false C26 0.094,1.771 2.833,2.188 2.74,0.417 10 false Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft)

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (DTC P0010)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and wait 5 seconds.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC P0010 is output A
DTC is not output B




A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
a.

Inspect the camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the C26 camshaft timing oil control valve assembly (for intake camshaft) connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C26-1 - C63-35 (OC1+) Always Below 1 Ω
C26-2 - C63-34 (OC1-) Always Below 1 Ω
C26-1 or C63-35 (OC1+) - Body ground and other terminals Always 10 kΩ or higher
C26-2 or C63-34 (OC1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT) - ECM)