Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0292315 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  P101D  A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON  


DESCRIPTION

Refer to DTC P2195.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>P2195

HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

The ECM has a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.

A384864E01
5.802,3.104 6.26,3.302 0.458,0.198 10 false ECM 6.125,1.438 7.063,1.646 0.938,0.208 10 false Duty Control 5.125,0.823 5.74,1.021 0.615,0.198 10 false HA1A 5.125,1.469 5.74,1.667 0.615,0.198 10 false A1A+ 5.125,2.344 5.74,2.542 0.615,0.198 10 false A1A- 4.563,0.823 5.177,1.021 0.615,0.198 10 false HA1A 4.583,1.469 5.198,1.667 0.615,0.198 10 false A1A+ 3.427,1.479 4.042,1.677 0.615,0.198 10 false A1A- 3.542,0.823 3.854,1.021 0.313,0.198 10 false +B 3.948,1.083 4.865,1.281 0.917,0.198 10 false Heater 3.938,1.792 4.854,1.99 0.917,0.198 10 false Sensor 3.51,2.115 5.135,2.344 1.625,0.229 10 false Air Fuel Ratio Sensor 2.885,1.094 3.583,1.281 0.698,0.188 10 false EFI NO. 3 5.104,2.667 5.719,2.865 0.615,0.198 10 false MREL 1.229,1.094 1.844,1.521 0.615,0.427 10 false EFI-MAIN NO. 1 0.302,0.917 2.135,1.115 1.833,0.198 10 false from Battery 0.135,0.094 2.854,0.313 2.719,0.219 10 false Reference (System Diagram of Sensor 1): 1.958,2.135 2.573,2.563 0.615,0.427 10 false EFI-MAIN NO. 1



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor heater current is below 0.8 A, even when the air fuel ratio sensor heater duty cycle is 30% or more (1 trip detection logic).
·

Open in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor heater current reaches the high limit (Hybrid IC high current limiter monitor input "Fail") (1 trip detection logic).
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored
P101D A/F Sensor Heater Circuit Performance Bank 1 Sensor 1 Stuck ON The heater current is higher than the specified value while the heater is not operating (1 trip detection logic).
·

Open or short in air fuel ratio sensor heater circuit

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.

The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.

The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.

The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.

When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

P0031
Heater output duty cycle 30% or higher

P0032
Heater output duty cycle Higher than 0%

P101D
Air fuel ratio sensor heater off current Higher than 11 A

CONFIRMATION DRIVING PATTERN

A198819E58
0.792,1.021 1.438,1.219 0.646,0.198 10 3000 rpm 1.031,1.771 1.5,2.115 0.469,0.344 10 Idling 0.229,2.052 1.396,2.396 1.167,0.344 10 Ignition Switch ON 1.927,2.156 2.333,2.521 0.406,0.365 10 [A] 2.76,1.656 3.167,2.031 0.406,0.375 10 [B] 4.021,0.896 4.333,1.115 0.313,0.219 10 [C] 5.385,1.646 5.833,1.958 0.448,0.313 10 [D] 2.365,2.604 3.844,3.01 1.479,0.406 10 5 minutes or more 4.854,2.604 6.229,2.833 1.375,0.229 10 5 minutes or more 3.896,2.604 4.635,2.844 0.74,0.24 10 1 minute 5.969,3.021 6.323,3.323 0.354,0.302 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine and idle it for 5 minutes or more [B].

9.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

10.

Idle the engine for 5 minutes or more [D].

11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0031, P0032 or P101D.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [E] again.




WIRING DIAGRAM

A384843E05
3.677,0.813 3.99,1.01 0.313,0.198 10 false +B 3.667,1.573 4.01,1.74 0.344,0.167 10 false A1A- 4.292,0.802 4.792,0.99 0.5,0.188 10 false HA1A 4.313,1.563 4.708,1.771 0.396,0.208 10 false A1A+ 6.073,0.802 6.5,1 0.427,0.198 10 false HA1A 6.073,1.563 6.5,1.76 0.427,0.198 10 false A1A+ 6.073,2.563 6.5,2.76 0.427,0.198 10 false A1A- 6.073,3.76 6.5,3.958 0.427,0.198 10 false MREL 5.177,2.906 5.49,3.104 0.313,0.198 10 false * 6.333,4.375 6.76,4.573 0.427,0.198 10 false ECM 3.615,2.354 5,2.573 1.385,0.219 10 false Air Fuel Ratio Sensor 0.49,2.865 1.01,3.052 0.521,0.188 10 false Battery 0.469,4.229 1.688,4.427 1.219,0.198 10 false *: Shielded 4.75,0.792 4.948,0.99 0.198,0.198 10 false 1 4.771,1.573 4.969,1.771 0.198,0.198 10 false 3 3.5,1.594 3.698,1.792 0.198,0.198 10 false 4 3.615,2.177 3.958,2.365 0.344,0.188 10 false C25 3.51,0.813 3.708,1.01 0.198,0.198 10 false 2 5.74,0.708 5.969,0.906 0.229,0.198 10 false 27 5.698,1.479 6.052,1.708 0.354,0.229 10 false 100 5.698,2.458 6.052,2.688 0.354,0.229 10 false 132 5.729,3.656 5.969,3.875 0.24,0.219 10 false 46 5.698,1.677 6.052,1.906 0.354,0.229 10 false C63 5.698,2.656 6.052,2.885 0.354,0.229 10 false C63 5.698,0.906 6.052,1.135 0.354,0.229 10 false C63 1.563,2.01 2.625,2.417 1.063,0.406 10 false EFI-MAIN NO. 1 5.708,3.854 6.063,4.083 0.354,0.229 10 false A38 2.844,1.063 3.573,1.333 0.729,0.271 10 false EFI NO. 3 0.438,1.083 1.5,1.417 1.063,0.333 10 false EFI-MAIN NO. 1 0.354,1.76 1.417,2.094 1.063,0.333 10 false BATT MAIN 2.375,1.542 2.531,1.74 0.156,0.198 10 false 1 1.615,1.583 1.771,1.781 0.156,0.198 10 false 2 1.615,0.844 1.771,1.042 0.156,0.198 10 false 5 2.365,0.833 2.521,1.031 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F Heater Duty #1].

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Change the fuel injection volume using the Control the Injection Volume for A/F Sensor function provided in the Active Test and monitor the air fuel ratio sensor output voltage (Click here Engine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>P0136). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
a.

Inspect the air fuel ratio sensor.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR)
a.
A395477C02
0.667,2.083 1.167,2.333 0.5,0.25 1.927,2.01 2.354,1.573 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.813,2.125 1.125,2.323 0.313,0.198 10 false C25 2.438,1.458 2.75,1.656 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C25-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - AIR FUEL RATIO SENSOR)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the C25 air fuel ratio sensor connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C63-27 (HA1A) Always Below 1 Ω
C25-1 (HA1A) or C63-27 (HA1A) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0031, P0032 OR P101D)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

j.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0031, P0032 or P101D is output B




A

B

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - AIR FUEL RATIO SENSOR)
a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Disconnect the C25 air fuel ratio sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 1 relay holder) - C25-2 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 1 relay holder) or C25-2 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT EFI-MAIN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - AIR FUEL RATIO SENSOR)

6.INSPECT EFI-MAIN NO. 1 RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)

NG

REPLACE EFI-MAIN NO. 1 RELAY

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY)
A384880C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *1 0.26,1.813 0.573,2.01 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO.1 Relay Holder


a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1 relay holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO.1 RELAY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY)

8.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO.1 RELAY - ECM)
a.

Remove the EFI-MAIN NO.1 relay from the No. 1 engine room relay block.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (EFI-MAIN NO. 1 relay holder) - A38-46 (MREL) Always Below 1 Ω
1 (EFI-MAIN NO. 1 relay holder) or A38-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher



HINT:

If a short is detected in any of the above circuits, there may be a malfunction in the circuit of a connected ECU.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO.1 RELAY - ECM)

9.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)
A384880C01
0.083,0.073 0.396,0.271 0.313,0.198 10 false *1 0.26,1.813 0.573,2.01 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO.1 Relay Holder


a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 1 relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND)