Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292320 DIFFERENTIAL OIL SEAL A

EC6A MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front drive shaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

PROCEDURE

Hide 1.REMOVE FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

Hide 2.REMOVE FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)

Hide 43420H 3.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C356466N01
0.688,2.135 0.688,1.771 false 1.719,3.083 1.719,2.885 false 0.573,2.146 0.917,2.354 0.344,0.208 10 false SST 1.583,3.115 1.927,3.323 0.344,0.208 10 false SST

Using SST, remove the front drive shaft oil seal LH from the manual transaxle assembly.

SST
09308-00010  


Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C356467N01
2.646,1.792 2.646,1.542 true 1.688,3.063 1.688,2.896 false 2.521,1.844 2.885,2.073 0.365,0.229 10 true SST 1.563,3.083 1.927,3.313 0.365,0.229 10 false SST

Using SST, remove the front drive shaft oil seal RH from the manual transaxle assembly.

SST
09308-00010  


Hide 43420H 5.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C356468N01
1.521,1.75 1.521,1.531 false 2.031,3.01 2.031,2.792 false 1.406,1.771 1.781,1.99 0.375,0.219 10 false SST 1.917,3.031 2.292,3.25 0.375,0.219 10 false SST

Coat the lip of a new front drive shaft oil seal LH with MP grease.


b.

Using SST and a hammer, tap in the front drive shaft oil seal LH to the manual transaxle assembly.

SST
09316-60011  (09316-00011)

Standard Depth:

10.6 to 11.6 mm (0.417 to 0.457 in.)


NOTICE:

Do not damage the front drive shaft oil seal LH lip.



Hide 43410M 6.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C356469N01
1.427,1.104 1.917,1.813 1.917,1.813 2.063,1.323 true 1.906,1.771 1.635,1.208 true 1.479,2.74 1.646,2.99 1.646,2.99 1.031,2.844 false 1.615,2.979 1.25,2.802 false 1.781,1.854 2.135,2.052 0.354,0.198 10 true SST 1.677,2.938 2.031,3.135 0.354,0.198 10 false SST

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.

Using SST and a hammer, tap in the front drive shaft oil seal RH to the manual transaxle assembly.

SST
09630-24014  (09620-24051)
09950-60010  (09951-00410, 09951-00530, 09952-06010)
09950-70010  (09951-07100)

Standard Depth:

1.2 to 2.2 mm (0.0472 to 0.0866 in.)


NOTICE:

Do not damage the front drive shaft oil seal RH lip.



Hide 7.INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

Hide 8.INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)