Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)
RM32H0E _52 Drivetrain _060137 DRIVE SHAFT / PROPELLER SHAFT _0294913 FRONT DRIVE SHAFT ASSEMBLY(for TMC Made) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEELS

Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 3.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 4.REMOVE REAR ENGINE UNDER COVER RH

Hide 5.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 6.DRAIN MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 7.DRAIN TRANSFER OIL (for AWD)

Hide 43502H 8.REMOVE FRONT AXLE SHAFT NUT

a.
C343035N01
2.406,1.708 2.406,1.396 false 2.302,1.74 2.76,1.938 0.458,0.198 10 false SST

Using SST and a hammer, release the staked part of the front axle shaft nut.

SST
09930-00010  

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the threads of the drive shaft may be damaged.



b.

While applying the brakes, remove the front axle shaft nut.


Hide 9.SEPARATE FRONT SPEED SENSOR

Hide 10.SEPARATE TIE ROD END SUB-ASSEMBLY

Hide 48810 11.SEPARATE FRONT STABILIZER LINK ASSEMBLY

Hide 48069 12.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 13.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

Hide 43420 14.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

a.
C343036N02
2.125,1.76 1.406,1.906 1.406,1.906 1.865,1.146 true 1.115,1.854 1.573,2.052 0.458,0.198 10 false SST

Using SST, remove the front drive shaft assembly LH.

SST
09520-01010  
09520-24010  (09520-32040)

NOTICE:
·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Do not drop the front drive shaft assembly LH.




Hide 43410 15.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

a.

for 2WD:

i.

Perform the same procedure as for the LH side.



b.

for AWD:

i.
C360102

Separate the drive shaft bearing bracket hole snap ring from the drive shaft bearing bracket.


ii.

Remove the bolt and front drive shaft assembly RH from the drive shaft bearing bracket.

NOTICE:
·

Be careful not to damage the transfer case oil seal RH, inboard joint boot and drive shaft dust cover.

·

Be careful not to drop the front drive shaft assembly RH.



HINT:

If the spline connection is stiff, using a brass bar and hammer, lightly tap the inboard joint assembly to remove it.



iii.

Remove the drive shaft bearing bracket hole snap ring from the front drive shaft assembly RH.



Hide 43030B 16.REMOVE FRONT DRIVE INBOARD JOINT HOLE SNAP RING

a.
C057543

Using a screwdriver, remove the front drive inboard joint hole snap ring.