Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
43040B
1.INSTALL FRONT DRIVE INBOARD JOINT HOLE SNAP RING
Install a new front drive inboard joint hole snap ring.
43420
2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
for CVT:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.
for Manual Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine Manual Transmission Gear Oil LV.
Coat the lip of the front drive shaft oil seal LH with MP grease.
Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.
Face the end gap of the front drive shaft hole snap ring downward.
Do not damage the front drive shaft oil seal LH.
Do not damage the front axle inboard joint boot.
Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.
Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.
|
Toyota Body Grease W |
Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to each of the 4 areas shown in the illustration.
| *a | Matchmark |
Align the matchmarks and install the front drive shaft assembly LH to the front axle hub sub-assembly.
Do not push the front axle assembly towards the outside of the vehicle any further than necessary.
Check that there is no foreign matter on the deflector or contact surfaces.
Do not damage the front drive shaft outboard joint boot.
Do not damage the front disc brake dust cover.
Do not damage the deflector.
43410
3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 8NR-FTS)
for CVT, 2WD:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.
for Manual Transaxle:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine Manual Transmission Gear Oil LV.
Coat the lip of the front drive shaft oil seal RH with MP grease.
for AWD:
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.
Install a new drive shaft bearing bracket hole snap ring to the front drive shaft assembly RH.
Coat the lip of the transfer case oil seal RH with MP grease.
Align the shaft splines and securely install the front drive shaft assembly RH.
Be careful not to damage the front drive shaft oil seal RH, inboard joint boot and drive shaft dust cover.
When inserting the front drive shaft assembly RH, keep it level.
Install the drive shaft bearing bracket hole snap ring and a new bolt.
Perform the same procedure as for the LH side.
43410
4.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 3ZR-FAE)
Coat the splines of the front drive inboard joint assembly with Toyota Genuine CVT Fluid FE.
Coat the lip of the front drive shaft oil seal RH with MP grease.
Align the shaft splines and securely install the front drive shaft assembly RH.
Be careful not to damage the front drive shaft oil seal RH, inboard joint boot and drive shaft dust cover.
When inserting the front drive shaft assembly RH, keep it level.
Install the front drive shaft assembly RH with the 2 bolts.
Perform the same procedure as for the LH side.
48068
5.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
6.INSTALL FRONT STABILIZER LINK ASSEMBLY
45047
7.CONNECT TIE ROD END SUB-ASSEMBLY
89543
8.INSTALL FRONT SPEED SENSOR
43502H
9.INSTALL FRONT AXLE SHAFT NUT
Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.
Be sure to perform this work even when using a new front drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.
Using a 30 mm deep socket wrench, install the front axle shaft nut.
Keep depressing the brake pedal to prevent the drive shaft from rotating.
Using a chisel and a hammer, stake the front axle shaft nut.
10.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)
for 8NR-FTS:
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
for 3ZR-FAE:
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE FLUID>ADJUSTMENT
11.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)
12.ADD TRANSFER OIL (for AWD)
13.INSPECT MANUAL TRANSAXLE OIL (for Manual Transaxle)
14.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK (for CVT)
15.INSPECT MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)
16.INSPECT TRANSFER OIL LEAK (for AWD)
17.INSTALL FRONT WHEELS
18.ADJUST FRONT WHEEL ALIGNMENT
51444A
19.INSTALL REAR ENGINE UNDER COVER LH
for 8NR-FTS:
Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
51443C
20.INSTALL REAR ENGINE UNDER COVER RH
for 8NR-FTS:
Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
51441
21.INSTALL NO. 1 ENGINE UNDER COVER
for 8NR-FTS:
Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 3ZR-FAE:
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
22.CHECK FOR SPEED SENSOR SIGNAL