Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292533 MANUAL TRANSAXLE SYSTEM C

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P071531  Input/Turbine Speed Sensor "A" No Signal  


DESCRIPTION

The transmission revolution sensor is mounted on the transaxle. The ECM calculates the transaxle input shaft speed using the sensor. When the input shaft rotates, the sensor generates a pulse signal and sends the signal to the ECM. The ECM calculates the input shaft speed based on the signal. If the input shaft speed falls below a threshold despite the engine running, the ECM interprets this as a malfunction in the transmission revolution sensor circuit. The ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071531 Input/Turbine Speed Sensor "A" No Signal While driving after warm-up with clutch engaged, transmission input speed is not input (1 trip detection logic)
·

Harness and connector

·

Transmission revolution sensor

·

ECM


Does not come on DTC stored SAE Code:
P0717

WIRING DIAGRAM

C364960E02
0.938,3.198 3.25,3.458 2.313,0.26 10 false Transmission Revolution Sensor 0.927,3.063 1.385,3.26 0.458,0.198 10 false C60 5.26,3.708 5.719,3.906 0.458,0.198 10 false C62 5.26,3.885 5.719,4.083 0.458,0.198 10 false ECM 5.104,1.552 5.719,1.75 0.615,0.198 10 false NIM+ 5.104,2.531 5.719,2.729 0.615,0.198 10 false NIM- 1.75,1.563 2.365,1.76 0.615,0.198 10 false NCO+ 1.75,2.531 2.365,2.729 0.615,0.198 10 false NCO- 4.802,1.552 5.115,1.75 0.313,0.198 10 false 44 4.813,2.531 5.125,2.729 0.313,0.198 10 false 43 2.25,1.563 2.406,1.76 0.156,0.198 10 false 2 2.229,2.51 2.385,2.708 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.

Click hereDrivetrain>EC6A (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (1) again.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED AND NIM SENSOR SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 372 211

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
600 to 700 rpm: Idling (shift lever in neutral, engine warmed up and A/C off) When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

f.

Enter the following menus: Powertrain / Transmission / Data List

Powertrain > Transmission > Data List
Tester Display
NIM Sensor Speed
50003 373 539

g.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NIM Sensor Speed Input shaft speed (NIM) Min.: 0 rpm
Max.: 16383 rpm
Input shaft speed (NIM) equal to engine speed (NE): Clutch pedal not depressed, vehicle running -

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION REVOLUTION SENSOR

B

7.REPLACE ECM
2.INSPECT TRANSMISSION REVOLUTION SENSOR
a.
C168336C33
1.994,1.633 2.181,1.795 0.186,0.161 10 *c 0.685,0.198 0.871,0.359 0.186,0.161 10 *a 2.296,0.198 2.482,0.359 0.186,0.161 10 *b
*a Correct
*b Incorrect
*c Clearance


Check the transmission revolution sensor installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)

NG

SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)
a.

Disconnect the C60 transmission revolution sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-2 (NCO+) - C62-44 (NIM+) Always Below 1 Ω
C60-1 (NCO-) - C62-43 (NIM-) Always Below 1 Ω
C60-2 (NCO+) - Body ground Always 10 kΩ or higher
C60-1 (NCO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT TRANSMISSION REVOLUTION SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT TRANSMISSION REVOLUTION SENSOR
a.

Inspect the transmission revolution sensor.

Click hereDrivetrain>EC6A (MANUAL TRANSMISSION / TRANSAXLE)>SPEED SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT COUNTER SHAFT (TEETH OF COUNTERSHAFT 2ND SPEED GEAR)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR

5.INSPECT COUNTER SHAFT (TEETH OF COUNTERSHAFT 2ND SPEED GEAR)
a.

Inspect the teeth of the countershaft 2nd speed gear.

OK:

No tooth damage on countershaft 2nd speed gear.



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT