Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit (PRNDL Input)  


DESCRIPTION

The park/neutral position switch and transmission control switch (shift lock control unit assembly) detect the shift lever position and send signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit (PRNDL Input) When the ignition switch is ON and the battery voltage is 10.5 V or more, any one of the following conditions is met (2 trip detection logic):
·

2 or more signals are ON simultaneously for 2 seconds or more for (NSW, P, N), R, D input signals.

·

NSW, P, R, N, D input signals are all OFF simultaneously for 60 seconds or more.

·

When the S signal (M position switch signal) is ON, any of the NSW, P, R, N input signals is ON simultaneously for 2 seconds or more.


·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

Transmission control switch

(Shift lock control unit assembly)

·

ECM


Comes on DTC stored

DTC Detection Condition Patterns:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnostic Condition Ignition switch ON and battery voltage is 10.5 V or more ○ ○ ○
Malfunction Condition 2 or more signals are ON simultaneously for (NSW, P, N), R, D input signals. ○ - -
NSW, P, R, N, D input signals are all OFF simultaneously. - ○ -
When the S signal (M position switch signal) is ON, any of the NSW, P, R, N input signals is ON simultaneously. - - ○
Duration 2 seconds or more 60 seconds or more 2 seconds or more
Detection Logic 2 trip detection logic 2 trip detection logic 2 trip detection logic

HINT:

This DTC is output when any one of the above detection patterns is met.


MONITOR DESCRIPTION

For safety, the park/neutral position switch detects the gearshift position so that engine can be started only when the vehicle is in the P or N shift position.

When the park/neutral position switch and shift lock control unit assembly (transmission control switch) send more than one signal at a time from switch positions P, R, N, D, M, the ECM interprets this as a fault in the switch. The ECM will turn on the MIL and store the DTC.

WIRING DIAGRAM

C356646E05
0.25,1.167 1.656,1.708 1.406,0.542 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.25,2.063 1.677,2.5 1.427,0.438 10 false from Ignition or Starter Switch Assembly*2 0.802,3.052 1.583,3.25 0.781,0.198 10 false BKUP LP 2.51,1.302 2.667,1.5 0.156,0.198 10 false 4 2.76,1.302 2.917,1.5 0.156,0.198 10 false B 3.927,1.292 4.083,1.49 0.156,0.198 10 false L 4.188,1.281 4.344,1.479 0.156,0.198 10 false 9 3.865,1.99 4.177,2.188 0.313,0.198 10 false PL 4.188,1.99 4.344,2.188 0.156,0.198 10 false 3 3.875,2.531 4.188,2.729 0.313,0.198 10 false RL 4.188,2.531 4.344,2.729 0.156,0.198 10 false 2 3.885,3.083 4.198,3.281 0.313,0.198 10 false NL 4.188,3.083 4.344,3.281 0.156,0.198 10 false 8 3.865,3.615 4.177,3.813 0.313,0.198 10 false DL 4.198,3.604 4.354,3.802 0.156,0.198 10 false 7 2.75,2.802 3.063,3 0.313,0.198 10 false RB 2.375,4.125 2.833,4.323 0.458,0.198 10 false C36 2.365,4.271 4.448,4.521 2.083,0.25 10 false Park/Neutral Position Switch 2.427,5.292 2.885,5.49 0.458,0.198 10 false F17 2.417,5.448 4.448,5.771 2.031,0.323 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 0.083,6 2.615,6.24 2.531,0.24 10 false *1: w/ Smart Entry and Start System 0.083,6.333 2.51,6.552 2.427,0.219 10 false *2: w/o Smart Entry and Start System 5.958,5.635 6.417,5.833 0.458,0.198 10 false ECM 5.521,0.604 5.979,0.802 0.458,0.198 10 false NSW 5.51,1.271 5.969,1.469 0.458,0.198 10 false STA 5.531,1.99 5.688,2.188 0.156,0.198 10 false P 5.531,2.542 5.688,2.74 0.156,0.198 10 false R 5.521,3.063 5.677,3.26 0.156,0.198 10 false N 5.521,3.594 5.677,3.792 0.156,0.198 10 false D 5.521,4.844 5.677,5.042 0.156,0.198 10 false S 3.917,4.865 4.073,5.063 0.156,0.198 10 false S 2.75,4.854 3.063,5.052 0.313,0.198 10 false IG 4.177,4.833 4.333,5.031 0.156,0.198 10 false 5 2.51,4.802 2.667,5 0.156,0.198 10 false 4 5.188,0.542 5.5,0.74 0.313,0.198 10 false 23 5.188,1.219 5.5,1.417 0.313,0.198 10 false 29 5.188,1.906 5.5,2.104 0.313,0.198 10 false 70 5.188,2.469 5.5,2.667 0.313,0.198 10 false 64 5.188,2.99 5.5,3.188 0.313,0.198 10 false 69 5.188,3.521 5.5,3.719 0.313,0.198 10 false 65 5.188,4.771 5.5,4.969 0.313,0.198 10 false 59 5.125,0.708 5.583,0.906 0.458,0.198 10 false A38 5.125,4.969 5.583,5.167 0.458,0.198 10 false A38 5.125,1.385 5.583,1.583 0.458,0.198 10 false A38 5.135,2.104 5.594,2.302 0.458,0.198 10 false C63 5.125,2.646 5.583,2.844 0.458,0.198 10 false C63 5.125,3.167 5.583,3.365 0.458,0.198 10 false C63 5.125,3.708 5.583,3.906 0.458,0.198 10 false C63 0.771,5.135 1.938,5.344 1.167,0.208 10 false ECU-IG1 NO .1 2.49,2.802 2.646,3 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON.

2.

Wait with the shift lever in each position (P, R, N, D and M) for 60 seconds or more each.

3.

Wait for 2 seconds or more with the shift lever in M.

4.

Turn the ignition switch off.

5.

Perform steps (1) through (4) again.



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW SIGNAL AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 234 147,125,126,127,128

e.

According to the display on the GTS, read the Data List while driving.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D or M

·

ON: Shift lever in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

B

7.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

b.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Sport mode select switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-

Result:
Result Proceed to
Data display is within Normal Condition range A
Data display is not within Normal Condition range B



A

B

3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH (POWER SOURCE))
a.
C245154C44
0.438,1 0.865,1.292 0.427,0.292 2.271,1.646 2.042,1.646 2.042,1.646 1.865,1.302 true 0.313,0.302 0.625,0.5 0.313,0.198 10 false *a 0.542,1.073 1,1.271 0.458,0.198 10 false F17 2.344,1.563 2.656,1.76 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly (transmission control switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F17-4 (IG) - Body ground Ignition switch ON 11 to 14 V
F17-4 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

NG

CHECK POWER SOURCE CIRCUIT (TRANSMISSION CONTROL SWITCH)

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C10
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)
a.

Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-5 (S) - A38-59 (S) Always Below 1 Ω
F17-5 (S) - Body ground Always 10 kΩ or higher
A38-59 (S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)
a.
C330140C42
0.438,0.958 0.885,1.24 0.448,0.281 1.625,1 2.021,0.396 true 2.073,0.313 2.385,0.51 0.313,0.198 10 false RB 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.5,1.021 0.969,1.219 0.469,0.198 10 false C36
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
C36-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

8.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)

8.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C298182C03
0.969,1.792 1.344,1.302 true 1.323,1.813 1.469,1.302 true 1.844,1.813 1.708,1.302 true 1.823,0.948 2.292,0.313 true 1.594,0.948 1.771,0.313 true 1.417,0.948 1.229,0.302 true 1.271,0.948 0.854,0.302 true 2.344,0.25 2.656,0.448 0.313,0.198 10 false RB 1.833,0.25 2.146,0.448 0.313,0.198 10 false RL 1.042,0.25 1.354,0.448 0.313,0.198 10 false PL 0.74,0.25 1.052,0.448 0.313,0.198 10 false B 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a 0.865,1.75 1.177,1.948 0.313,0.198 10 false L 1.146,1.75 1.458,1.948 0.313,0.198 10 false NL 1.896,1.75 2.208,1.948 0.313,0.198 10 false DL
*a Component without harness connected
(Park/Neutral Position Switch)


Disconnect the C36 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P or N Below 1 Ω
Shift lever not in P or N 10 kΩ or higher
1 (RB) - 3 (PL) Shift lever in P Below 1 Ω
Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
Shift lever not in R 10 kΩ or higher
1 (RB) - 8 (NL) Shift lever in N Below 1 Ω
Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever in D or M Below 1 Ω
Shift lever not in D or M 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH

9.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the C36 park/neutral position switch connector.


b.

Disconnect the C63 and A38 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-3 (PL) - C63-70 (P) Always Below 1 Ω
C36-2 (RL) - C63-64 (R) Always Below 1 Ω
C36-8 (NL) - C63-69 (N) Always Below 1 Ω
C36-7 (DL) - C63-65 (D) Always Below 1 Ω
C36-4 (B) - A38-23 (NSW) Always Below 1 Ω
C36-3 (PL) or C63-70 (P) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (RL) or C63-64 (R) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (NL) or C63-69 (N) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (DL) or C63-65 (D) - Body ground and other terminals Always 10 kΩ or higher
C36-4 (B) or A38-23 (NSW) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)