The ECM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0841 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance | Either one of the following conditions is met (1 trip detection logic):
·
When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less for 2 seconds or more. ·
When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the difference between the calculated primary pulley pressure and target primary pulley pressure is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more. |
·
Oil pressure sensor ·
ECM |
Comes on | DTC stored |
| P2829 | Pressure Control Solenoid "K" Performance or Stuck Off | One of the following conditions is met (1 trip detection logic):
·
When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more. ·
When the vehicle speed is less than 8 km/h (5 mph), the ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value for 0.2 seconds or more. ·
When the oil pressure sensor output is less than 0.283 MPa (2.9 kgf/cm2, 41 psi) and the target gear ratio is 2.0 or more, the actual gear ratio is less than 1.0 for 1.5 seconds or more. |
·
Continuously variable transaxle assembly ·
ECM |
Comes on | DTC stored |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnostic Condition | The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more. | ○ | - |
| The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. | - | ○ | |
| Malfunction Condition | The oil pressure sensor output value is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less. | ○ | - |
| The difference between the calculated primary pulley pressure and target primary pulley pressure is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more. | - | ○ | |
| Duration | 2 seconds or more | 3 seconds or more | |
| Detection Logic | 1 trip detection logic | 1 trip detection logic | |
This DTC is output when either of the above detection patterns is met.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnostic Condition | The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. | ○ | - | - |
| The vehicle speed is less than 8 km/h (5 mph). | - | ○ | - | |
| The oil pressure sensor output value is less than 0.283 MPa (2.9 kgf/cm2, 41 psi) and the target gear ratio is 2.0 or more. | - | - | ○ | |
| Malfunction Condition | The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more. | ○ | - | - |
| The ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value. | - | ○ | - | |
| The actual gear ratio is less than 1.0. | - | - | ○ | |
| Duration | 3 seconds or more | 0.2 seconds or more | 1.5 seconds or more | |
| Detection Logic | 1 trip detection logic | 1 trip detection logic | 1 trip detection logic | |
This DTC is output when any one of the above detection patterns is met.
The ECM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or the oil pressure sensor is detected by the ECM, it illuminates the MIL and stores a DTC.
Do not perform a stall test if there are any people or objects near the vehicle.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform a stall test if any wheel chocks are out of position.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
The vehicle could begin moving suddenly, resulting in a serious accident.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D position test in Road Test.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Check for DTCs again.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
If any other DTCs besides P0841 or P2829 are output, perform troubleshooting for those DTCs first.
| Result | Proceed to |
|---|---|
| Both DTC P0841 and P2829 are output | A |
| Only DTC P0841 is output | B |
| Only DTC P2829 is output | C |
| P0841 and/or P2829 and other DTCs are output | D |
A
B
C
D
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| A/T Oil Pressure |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test ·
3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure sensor.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Airbag sensor assembly (Yaw rate and acceleration sensor) |
After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check for DTCs again.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P0841 and/or P2829 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Airbag sensor assembly (Yaw rate and acceleration sensor) |
After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check for DTCs again.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P2829 is output | A |
| DTCs are not output | B |
A
B
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| A/T Oil Pressure |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test ·
3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure sensor.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned value of the yaw rate and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Make sure to perform Reset Memory, yaw rate and acceleration sensor zero point calibration, and CVT oil pressure calibration when replacing any of the parts shown in the following table:
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Airbag sensor assembly (Yaw rate and acceleration sensor) |
After performing Reset Memory, always perform yaw rate and acceleration sensor (deceleration sensor zero point) calibration first, and then CVT oil pressure calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, deceleration sensor zero point calibration and CVT oil pressure calibration.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check for DTCs again.
Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P0841 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).
Perform this test with the A/C off.
Do not perform the stall speed test for longer than 5 seconds.
When performing the stall speed test more than once, make sure to wait 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| A/T Oil Pressure |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| A/T Oil Pressure | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test ·
3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test |
- |
| Result | Proceed to |
|---|---|
| Data display is within Normal Condition range | A |
| Data display is not within Normal Condition range | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT