Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292534 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0842  Transmission Fluid Pressure Sensor/Switch "A" Circuit Low  P0843  Transmission Fluid Pressure Sensor/Switch "A" Circuit High  


DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is output by the oil pressure sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0842 Transmission Fluid Pressure Sensor/Switch "A" Circuit Low When 2 seconds or more have elapsed after engine start, there is a short in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Oil pressure sensor

·

ECM


Comes on DTC stored
P0843 Transmission Fluid Pressure Sensor/Switch "A" Circuit High When 2 seconds or more have elapsed after engine start, there is an open or a short to +B in the oil pressure sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Oil pressure sensor

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the oil pressure sensor circuit. If there is an open or short in the oil pressure sensor circuit, the ECM detects the malfunction, illuminates the MIL and stores a DTC.

WIRING DIAGRAM

C318995E21
1.094,2.802 2.781,3 1.688,0.198 10 false Oil Pressure Sensor 5.323,3.073 6.135,3.438 0.813,0.365 10 false ECM 1.094,2.667 1.552,2.865 0.458,0.198 10 false C44 5.323,2.927 6.042,3.219 0.719,0.292 10 false C63 4.885,2.188 5.5,2.385 0.615,0.198 10 false EPTO 4.885,1.635 5.5,1.833 0.615,0.198 10 false PTO 4.885,1.146 5.5,1.344 0.615,0.198 10 false VCPT 2.156,1.24 2.771,1.438 0.615,0.198 10 false VC 2.073,1.729 2.688,1.927 0.615,0.198 10 false PTO 2.177,2.271 2.792,2.469 0.615,0.198 10 false E2 2.448,2.188 3.063,2.385 0.615,0.198 10 false 1 2.438,1.635 3.052,1.833 0.615,0.198 10 false 2 2.427,1.156 3.042,1.354 0.615,0.198 10 false 3 4.573,1.146 5.188,1.344 0.615,0.198 10 false 110 4.646,1.635 5.26,1.833 0.615,0.198 10 false 79 4.573,2.188 5.188,2.385 0.615,0.198 10 false 109 5.583,0.979 6.198,1.177 0.615,0.198 10 false 5 V

CAUTION / NOTICE / HINT

CAUTION:
·
C328174


·

Do not perform a stall test if there are any people or objects near the vehicle.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328171


·

Do not perform a stall test if any wheel chocks are out of position.

·

The vehicle could begin moving suddenly, resulting in a serious accident.


·
C328173


·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.

·

The vehicle could begin moving suddenly, resulting in a serious accident.



NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Start the engine and wait for 2 seconds or more.



PROCEDURE

1.READ VALUE USING GTS (A/T OIL PRESSURE)
CAUTION:
·

Do not perform a stall test if there are any people or objects near the vehicle.

·

Do not perform a stall test if any wheel chocks are out of position.

·

Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.



NOTICE:
·

This test must be conducted after checking and confirming that the engine is operating normally.

·

Perform this test while the CVT fluid temperature is between 50 and 100°C (122 and 212°F).

·

Perform this test with the A/C off.

·

Do not perform the stall speed test for longer than 5 seconds.



a.

Warm up the engine.


b.

Fully apply the parking brake and chock all 4 wheels.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

g.

Enter the following menus: Powertrain / Engine and ECT / Data List / Primary.

Powertrain > Engine and ECT > Data List
Tester Display
A/T Oil Pressure
50003 234 409

h.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value Min.: -64 MPa
Max.: 63.998 MPa
Secondary oil pressure inspection:
·

3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): D position stall speed test

·

3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): R position stall speed test


-

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)

B

6.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)
a.

Disconnect the C44 oil pressure sensor connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C44-1 (E2) - C63-109 (EPTO) Always Below 1 Ω
C44-2 (PTO) - C63-79 (PTO) Always Below 1 Ω
C44-3 (VC) - C63-110 (VCPT) Always Below 1 Ω
C44-1 (E2) or C63-109 (EPTO) - Body ground and other terminals Always 10 kΩ or higher
C44-2 (PTO) or C63-79 (PTO) - Body ground and other terminals Always 10 kΩ or higher
C44-3 (VC) or C63-110 (VCPT) - Body ground and other terminals Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C63-79 (PTO) - Body ground Ignition switch ON Below 1 V
C44-2 (PTO) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

3.CHECK ECM (VCPT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OIL PRESSURE SENSOR - ECM)

3.CHECK ECM (VCPT TERMINAL VOLTAGE)
a.
C125747C53
0.438,0.938 0.802,1.219 0.365,0.281 1.479,1.271 1.146,1.719 1.146,1.719 1.01,1.719 true 2.052,1.26 2.406,1.677 2.406,1.677 2.531,1.677 true 0.792,1.635 1.177,1.844 0.385,0.208 10 false E2 2.604,1.604 2.875,1.792 0.271,0.188 10 false VC 0.094,0.094 0.313,0.25 0.219,0.156 10 false *a 0.51,1.01 0.948,1.188 0.438,0.177 10 false C44
*a Front view of wire harness connector
(to Oil Pressure Sensor)


Disconnect the oil pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C44-3 (VC) - C44-1 (E2) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

4.REPLACE OIL PRESSURE SENSOR

NG

5.REPLACE ECM
4.REPLACE OIL PRESSURE SENSOR
a.

Replace the oil pressure sensor.

Click hereDrivetrain>K114 (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT