The ECM receives a signal from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft (secondary pulley) speed in order to control the gear ratio.
The transmission revolution sensor (NOUT) detects the continuously variable transaxle output shaft (secondary pulley) speed and sends a signal to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P072012 | Output Speed Sensor Circuit Short to Battery | There is no malfunction in transmission revolution sensor (NOUT) signals, and the transmission revolution sensor (NOUT) output voltage is higher than 1.8 V for 2 seconds (1 trip detection logic). | ·
Wire harness or connector ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored | SAE Code:
P077D |
| P072014 | Output Speed Sensor Circuit Short to Ground or Open | There is no malfunction in transmission revolution sensor (NOUT) signals, and the transmission revolution sensor (NOUT) output voltage is less than 0.2 V for 2 seconds (1 trip detection logic) | ·
Wire harness or connector ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored | SAE Code:
P077C |
| P072031 | Output Speed Sensor No Signal | All of the following conditions are met (1 trip detection logic):
·
Vehicle is driven with the shift lever in D ·
Output shaft speed is 300 rpm or more ·
No malfunctions are found in the park/neutral position switch ·
Output shaft speed indicated by the transmission revolution sensor (NOUT) is less than 300 rpm for 2 seconds |
·
Wire harness or connector ·
Transmission revolution sensor (NOUT) ·
ECM |
Comes on | DTC stored | SAE Code:
P0722 |
The ECM receives a signal from the transmission revolution sensor (NOUT) installed to the continuously variable transaxle and determines the output shaft (secondary pulley) speed in order to control the gear ratio.
If the ECM detects no signal from the transmission revolution sensor (NOUT) even while the vehicle is moving, it will determine that in the transmission revolution sensor (NOUT) is malfunctioning, illuminate the MIL and store a DTC.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle for 2 seconds or more at 7 km/h (4 mph) or more with the shift lever in D.
Check for DTCs again.
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
| Tester Display |
|---|
| NOUT Sensor Speed |
| NOUT Sensor Voltage |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| NOUT Sensor Speed | Secondary pulley speed (NOUT) | Min.: 0 rpm
Max.: 12750 rpm |
·
0 rpm: Vehicle stopped ·
Approximately 2700 rpm: Vehicle being driven at approximately 60 km/h (37 mph) |
Data is displayed in increments of 50 rpm. |
| NOUT Sensor Voltage | Transmission revolution sensor (NOUT) output voltage | Min.: 0.000 V
Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| Result | Proceed to |
|---|---|
| Data List value is not normal | A |
| Data List value is normal | B |
A
B
Remove the transmission revolution sensor (NOUT).
Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>REVOLUTION SENSOR>REMOVAL
Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.
| *1 | Battery | - | - |
| *a | Component without harness connected
(Transmission Revolution Sensor (NOUT)) |
*b | Magnet |
| *c | 5 mm or less | *d | Ammeter |
Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NOUT) to output a high/low signal while measuring the current.
Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.
Measure the current according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (NOTO) - 2 (NOTB) | Low signal | 4 to 8 mA |
| 1 (NOTO) - 2 (NOTB) | High signal | 12 to 16 mA |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C46 transmission revolution sensor (NOUT) connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-1 (NOTO) - C62-74 (NOTO) | Always | Below 1 Ω |
| C46-2 (NOTB) - C62-73 (NOTB) | Always | Below 1 Ω |
| C46-1 (NOTO) or C62-74 (NOTO) - Body ground and other terminals | Always | 10 kΩ or higher |
| C46-2 (NOTB) or C62-73 (NOTB) - Body ground and other terminals | Always | 10 kΩ or higher |
Connect the C62 ECM connector.
Connect the C46 transmission revolution sensor (NOUT) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT