Home › Drivetrain › K313 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0292538 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P061512  Starter Relay Circuit Short to Battery  


MONITOR DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.

If the ECM detects the Starter Control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds or more (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or more.

(c) The STA signal is on.


·

ST relay

·

Starter signal circuit

·

Park/neutral position switch

·

Certification ECU (Smart key ECU assembly)*1

·

Ignition or starter switch assembly*2

·

ECM


Comes on DTC stored SAE Code: P0617

*1: w/ Entry and Start System

*2: w/o Entry and Start System

WIRING DIAGRAM

Refer to SFI system DTC P061512.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P061512

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization when parts related to the continuously variable transaxle are replaced.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:
·

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

(a)

Drive the vehicle for 20 seconds or more under the following conditions:

*

Engine speed of 1000 rpm or more.

*

Vehicle speed of 20 km/h (12.43 mph) or more.





PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / Starter SW.

Powertrain > Transmission > Data List
Tester Display
Starter SW
50003 373 11

e.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Standard:
Switch Condition Starter SW
Ignition switch ON OFF



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.

Standard:
Condition Starter SW
Driving at 20 km/h (12 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, GTS connected and Data List item "Starter SW" selected.


Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".



A

B

2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)

C

8.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Transmission / Data List / Starter SW.

Powertrain > Transmission > Data List
Tester Display
Starter SW
50003 373 11

b.

Remove the ST relay from the No. 1 engine room relay block.


c.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON. A
The Data List item "Starter SW" changes from ON to OFF. B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A384829C18
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.167,1.646 0.479,1.844 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


HINT:

The purpose of this step is to check for ST relay holder voltage under abnormal conditions.


a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay holder 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

4.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
4.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
A384829C18
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.167,1.646 0.479,1.844 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the C36 park/neutral position switch connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A384829C18
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.167,1.646 0.479,1.844 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the A38 ECM connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

B

7.REPLACE ECM
6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the C36 park/neutral position switch connector.


c.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


d.

Remove the ST relay from the No. 1 engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-29 (STA), C36-9 (L), M66-20 (STA) or 2 (ST relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

8.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Transmission / Data List / Starter SW.

Powertrain > Transmission > Data List
Tester Display
Starter SW
50003 373 11

b.

Remove the ST relay from the No. 1 engine room relay block.


c.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter SW Starter signal OFF or ON
·

ON: Starter operating

·

OFF: Starter not operating


-
Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON. A
The Data List item "Starter SW" changes from ON to OFF. B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

B

REPLACE ST RELAY

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A384829C18
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.167,1.646 0.479,1.844 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


HINT:

The purpose of this step is to check for ST relay holder voltage under abnormal conditions.


a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay holder 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

11.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
11.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
A384829C18
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.167,1.646 0.479,1.844 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the C36 park/neutral position switch connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

12.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

12.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A384829C18
0.094,0.094 0.406,0.292 0.313,0.198 10 false *1 0.167,1.646 0.479,1.844 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the A38 ECM connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - ST RELAY)

B

13.REPLACE ECM
13.REPLACE ECM

Result:
Proceed to
NEXT



NEXT