Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › ENGINE › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292811 ENGINE G

3ZR-FAE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:
·
A345137

When working near the engine room while the engine has started or the power source mode is ignition switch to ON (IG), do not touch the fan and generator V belt or rotating components such as the fan, etc.

·

Touching the fan and generator V belt or rotating components such as the fan, etc. could result in your hand or clothing getting caught and pulled in.



PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 7.INSPECT VALVE AND ADJUSTER NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises. If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the preceding inspections.

HINT:

If any defects or problems are found during the inspections, perform valve lash adjuster assembly inspection.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION



Hide 8.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard Ignition Timing:

0 to 14 BTDC at idle


NOTICE:
·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Active Test Display
Connect the TC and TE1
Data List Display
IGN Advance
50004 234 13 29

vi.

Monitor IGN Advance of the Data List.

Standard Ignition Timing:

8 to 12 BTDC at idle


NOTICE:

When checking the ignition timing, the transaxle should be in neutral or park.



vii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / OFF.


viii.

Check that the ignition timing advances immediately when the engine speed is increased.


ix.

Turn the ignition switch off.


x.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.
A206183C51
1.771,1.479 2.083,1.917 2.083,1.917 2.167,1.917 true 1.604,0.927 1.333,0.396 1.333,0.396 1.219,0.396 true 0.073,0.083 0.438,0.385 0.365,0.302 10 false *a 2.208,1.833 2.521,2.031 0.313,0.198 10 false TC 1,0.313 1.396,0.552 0.396,0.24 10 false CG
*a DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminals before connecting them. Connecting the wrong terminals may result in damage to electrical components.

·

Check the ignition timing with the cooling fan off.

·

Turn off all electrical systems and the A/C.

·

When checking the ignition timing, the transaxle should be in neutral or park.




ii.

Connect the clip of the timing light to the ignition coil wire for the No. 1 cylinder.

NOTICE:

Use a timing light that detects the primary signal.



iii.

Inspect the ignition timing at idle.

Standard Ignition Timing:

8 to 12 BTDC at idle


NOTICE:

When checking the ignition timing, the transaxle should be in neutral or park.


HINT:

After running the engine at 1000 to 1300 rpm for 5 seconds, check that it returns to idle speed.



iv.

Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.


v.

Inspect the ignition timing at idle.

Standard Ignition Timing:

0 to 14 BTDC at idle



vi.

Check that the ignition timing advances immediately when the engine speed is increased.


vii.

Disconnect the clip of the timing light.



Hide 9.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and run it at idle.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

v.

Inspect the engine idle speed.

Standard Idle Speed:

710 to 810 rpm


NOTICE:
·

Turn off all electrical systems and the A/C.

·

Inspect the engine idle speed with the cooling fan off.

·

When checking the engine idle speed, the transaxle should be in neutral or park.




vi.

Turn the ignition switch off.


vii.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.
A206183C64
1.042,1.906 1.042,1.479 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 0.938,1.938 1.396,2.135 0.458,0.198 10 false TAC
*a DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18040  

NOTICE:

Be sure to connect the tachometer probe to the correct terminal. Connecting the wrong terminals may damage electrical components.



ii.

Turn the ignition switch to ON.


iii.

Inspect the engine idle speed.

Standard Idle Speed:

710 to 810 rpm


NOTICE:
·

Turn off all electrical systems and the A/C.

·

Inspect the engine idle speed with the cooling fans off.

·

When checking the engine idle speed, the transaxle should be in neutral or park.




iv.

Turn the ignition switch off.


v.

Disconnect the tachometer probe from terminal 9 (TAC) of the DLC3.



Hide 10.INSPECT COMPRESSION

NOTICE:

Keep the spark plug holes free of foreign matter when measuring the compression pressure.



b.

Warm up and stop the engine.


c.

Remove the 4 spark plugs.

Click hereGeneral>MAINTENANCE>3ZR-FAE SPARK PLUG>REMOVAL


d.

Disconnect the 4 fuel injector connectors.

NOTICE:

Disable fuel injection in order to prevent catalyst damage due to unburned gasoline.



e.

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard Compression Pressure:

1373 kPa (14.0 kgf/cm2, 199 psi)


Minimum Compression Pressure:

980 kPa (10.0 kgf/cm2, 142 psi)


Pressure Difference between Each Cylinder:

100 kPa (1.0 kgf/cm2, 15 psi)


NOTICE:
·

Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression pressure as quickly as possible.




iv.

If the cylinder compression pressure is low, pour a small amount of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the compression pressure stays low, a valve may be stuck or seated improperly, or there may be leaks in the gasket.





f.

Connect the 4 fuel injector connectors.


g.

Install the 4 spark plugs.

Click hereGeneral>MAINTENANCE>3ZR-FAE SPARK PLUG>INSTALLATION


h.

Clear the DTCs.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

NOTICE:

After the inspection, clear the DTCs, check for DTCs again and make sure the normal system code is output.



Hide 11.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Keep the engine at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe during idle.


d.

Immediately check the CO/HC concentration during idle and when the engine is running at 2500 rpm.

HINT:

When doing a 2 mode (with the engine idling/running at 2500 rpm) test, the measurement procedures are determined by applicable local regulations.

If the CO/HC concentration does not comply with the regulations, perform troubleshooting in the order given below.



ii.

See the following table for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problem Possible Cause
Normal High Rough idle
1.

Faulty ignition:

-

Incorrect timing

-

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaks in intake or exhaust valves

4.

Leaks in cylinders


Low High Rough idle (Fluctuating HC reading)
1.

Vacuum leaks:

-

PCV hoses

-

Intake manifold

-

Throttle body assembly

-

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle (Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty EFI systems:

-

Pressure regulator

-

Engine coolant temperature sensor

-

Mass air flow meter

-

ECM

-

Injector assemblies

-

Throttle body assembly