Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for VALEO Made) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0293719 AIR CONDITIONING UNIT(for VALEO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for VALEO Made)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles



PROCEDURE

Hide 55990B 1.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112349

Engage the claws to install the lower defroster nozzle assembly.


Hide 2.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.


Hide 3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:

When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.


a.

Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112520C01
0,0 0,0 false
V113147

Install in this Direction - -



b.
I112356

Connect 2 connectors.


c.

Engage the clamps.


d.

Install the 5 bolts.

Torque:
Bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)
Bolt B : 23.6 N*m (241 kgf*cm, 17 ft.*lbf)

I113816N01
1.021,3.865 1.177,4.063 0.156,0.198 10 true A 1.042,2.906 1.198,3.104 0.156,0.198 10 true A 6.74,1.406 6.896,1.604 0.156,0.198 10 true A 6.75,2.333 6.906,2.531 0.156,0.198 10 true A 1.094,2.458 1.25,2.656 0.156,0.198 10 true B


e.

Temporarily install the nut.


f.

Install the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 88539J 4.CONNECT DRAIN COOLER HOSE

a.
I112352C01
1.656,3.083 1.24,2.896 true 1.688,3 1.948,3.208 0.26,0.208 10 true *1
*1 Cooler Unit Drain Hose Grommet


Connect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while connecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 82141 5.CONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Engage clamps and hook to connect the instrument panel wire.

I113769C03
0.469,1.073 0.729,0.885 true 1.646,1.365 1.865,1.219 true 3.552,1.01 3.083,1.094 3.083,1.094 2.979,0.813 true 4.521,0.375 3.958,0.188 3.958,0.188 4.177,0.385 true 6.219,0.604 5.354,0.813 5.354,0.813 5.552,1.031 true 6.167,1.313 6.448,1.354 true 6.25,2.542 6.844,2.906 6.844,2.906 6.448,3.146 true 3.875,4.281 3.708,4.979 3.708,4.979 3.198,4.281 true 2.5,4.333 2.635,3.76 2.635,3.76 2.25,4.073 true 2.531,4.656 2.583,4.854 true 0.833,4.938 1.063,5.094 true 0.542,5.271 0.771,5.427 true 0.729,0.75 0.948,0.948 0.219,0.198 10 true *a 0.344,5.146 0.552,5.333 0.208,0.188 10 true *b 1.448,1.271 1.667,1.469 0.219,0.198 10 true *a 2.99,1.125 3.208,1.323 0.219,0.198 10 true *a 3.74,0.073 3.958,0.271 0.219,0.198 10 true *a 5.104,0.698 5.323,0.896 0.219,0.198 10 true *a 5.948,1.177 6.167,1.375 0.219,0.198 10 true *a 6.875,2.802 7.094,3 0.219,0.198 10 true *a 3.635,5 3.854,5.198 0.219,0.198 10 true *a 2.677,3.635 2.896,3.833 0.219,0.198 10 true *a 2.51,4.865 2.729,5.063 0.219,0.198 10 true *a 0.969,5.094 1.188,5.292 0.219,0.198 10 true *a 1.583,0.49 1.74,0.688 0.156,0.198 10 true A 1.51,0.729 1.667,0.927 0.156,0.198 10 true A 6.042,0.844 6.198,1.042 0.156,0.198 10 true A 6.823,3.625 6.979,3.823 0.156,0.198 10 true B
*a Clamp *b Hook



ii.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Install the 4 ground wires with the 4 bolts.

Torque:
Bolt A : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-06995) : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-W0017) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)


iv.

Install the bolt and screw.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


v.

Connect each connector.



b.

for RHD:

i.

Engage clamps and hook to connect the instrument panel wire.

I113770C01
0.635,1 0.896,1.125 true 1.615,0.323 1.344,0.521 true 2.667,1.135 2.771,1.281 true 3.323,0.979 3.75,1.208 3.75,1.208 4.177,0.927 true 6.469,0.792 6.656,1.042 true 6.583,4.906 6.75,4.521 6.75,4.521 6.552,4.125 true 6.229,5.479 6.438,5.583 true 3.26,4.375 3.615,4.854 3.615,4.854 3.833,4.302 true 2.469,4.74 2.677,4.615 true 0.5,5.271 0.719,5.438 true 0.844,4.958 1.063,5.125 true 0.917,1.052 1.115,1.24 0.198,0.188 10 true *a 0.26,5.146 0.469,5.344 0.208,0.198 10 true *b 1.156,0.427 1.354,0.615 0.198,0.188 10 true *a 2.688,1.281 2.885,1.469 0.198,0.188 10 true *a 3.646,1.219 3.844,1.406 0.198,0.188 10 true *a 6.281,0.688 6.479,0.875 0.198,0.188 10 true *a 5.521,4.042 5.719,4.229 0.198,0.188 10 true A 5.604,4.354 5.802,4.542 0.198,0.188 10 true A 6.802,4.417 7,4.604 0.198,0.188 10 true *a 6.01,5.375 6.208,5.563 0.198,0.188 10 true *a 3.51,4.854 3.708,5.042 0.198,0.188 10 true *a 2.688,4.51 2.885,4.698 0.198,0.188 10 true *a 0.979,5.135 1.177,5.323 0.198,0.188 10 true *a 6.833,5.083 7.031,5.271 0.198,0.188 10 false B 5.625,0.292 5.823,0.479 0.198,0.188 10 true C 5.698,0.615 5.896,0.802 0.198,0.188 10 true C 1.927,0.344 2.125,0.531 0.198,0.188 10 true C
*a Clamp *b Hook



ii.

Install the instrument panel junction block assembly with main body ECU with the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


iii.

Install the 2 nuts A.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


iv.

Install the 4 ground wires with the 4 bolts.

Torque:
Bolt B (Part No. 90119-06995) : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
Bolt B (Part No. 90119-W0017) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Bolt C : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)


v.

Install the bolt and screw.

Torque:
Bolt : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


vi.

Connect each connector.



Hide 55308B 6.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112348

Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.

Torque:
Bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Nut : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Engage the clamp and claws.


Hide 55307C 7.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
I112542

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.

Install the ground wire with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


iv.

Engage the clamps to connect the wire harness.



b.

for RHD:

i.

Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.
I113736

Install the ground wire with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


iv.

Engage the clamps to connect the wire harness.



Hide 55306A 8.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.

Install the No. 1 instrument panel brace sub-assembly with the bolt and 2 nuts.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.
I113757

Engage the clamps to connect the wire harness.



b.

for RHD:

i.

Install the No. 1 instrument panel brace sub-assembly with the bolt and 2 nuts.

Torque:
Bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Nut : 18 N*m (184 kgf*cm, 13 ft.*lbf)


ii.

Temporarily install the screw.

HINT:

Do not fully tighten the screw.



iii.
I113738

Engage the clamps to connect the wire harness.



c.

w/ PTC Heater:

i.

Install the bolt to connect the ground wire.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)



d.

Install the relay block assembly with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 9.INSTALL AIR CONDITIONER UNIT ASSEMBLY

a.

for LHD:

i.

Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit.

I112561N01
1.896,0.896 2.052,1.094 0.156,0.198 10 true 1 4.323,0.844 4.479,1.042 0.156,0.198 10 true 3 6.146,0.844 6.302,1.042 0.156,0.198 10 true 2 1.958,4.365 2.115,4.563 0.156,0.198 10 true 4 3.854,4.375 4.01,4.573 0.156,0.198 10 true 5 5.625,4.375 5.781,4.573 0.156,0.198 10 true 6

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.

for RHD:

i.

Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit.

I112550E01
1.896,0.927 2.052,1.125 0.156,0.198 10 true 2 4.208,0.917 4.365,1.115 0.156,0.198 10 true 1 6.115,0.896 6.271,1.094 0.156,0.198 10 true 3 1.99,4.406 2.146,4.604 0.156,0.198 10 true 6 5.594,4.385 5.75,4.583 0.156,0.198 10 true 4

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 87212 10.INSTALL REAR NO. 1 AIR DUCT (w/ Rear Air Duct)

a.
I112806C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 1 air duct as shown in the illustration.


Hide 87212F 11.INSTALL REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

a.
I112519C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 2 air duct as shown in the illustration.


Hide 87212G 12.INSTALL REAR NO. 3 AIR DUCT (w/ Rear Air Duct)

a.
I112515C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 3 air duct as shown in the illustration.


Hide 87212H 13.INSTALL REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

a.
I112514C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 4 air duct as shown in the illustration.


b.
I112513C01
0,0 0,0 false
V113147

Install in this Direction


Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the clamps.


d.

Install the clip.


e.

Install the 2 front floor carpet clips.


Hide 87212J 14.INSTALL REAR NO. 5 AIR DUCT (w/ Rear Air Duct)

a.
I112518C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 5 air duct as shown in the illustration.


Hide 87212K 15.INSTALL REAR NO. 6 AIR DUCT (w/ Rear Air Duct)

a.
I112517C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear No. 6 air duct as shown in the illustration.


Hide 55215D 16.INSTALL NO. 3 DASH PANEL INSULATOR PAD

a.
I112343

Engage the clips to install the No. 3 dash panel insulator pad.


b.
I112516C01
0,0 0,0 false
V113147

Install in this Direction


Install the front floor carpet assembly to its original position as shown in the illustration.


c.

Engage the clamps.


d.

Install the clip.


e.

Install the 2 front floor carpet clips.


Hide 88625Q 17.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.

Connect the aspirator and connector to install the cooler thermistor (room temperature sensor).


Hide 82877 18.INSTALL ECU INTEGRATION BOX RH (for LHD)

Hide 82878 19.INSTALL ECU INTEGRATION BOX LH (for RHD)

Hide 89340A 20.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 85940 21.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY

Hide 22.INSTALL STEERING COLUMN ASSEMBLY

Hide 55401E 23.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 24.INSTALL FRONT SEAT ASSEMBLY LH

Hide 25.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 88716A 26.CONNECT COOLER REFRIGERANT LIQUID PIPE A

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A.


b.

Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.

Compressor Oil:

VC100YF or equivalent



c.

Install the O-ring to the cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A.


Hide 88707 27.CONNECT SUCTION PIPE SUB-ASSEMBLY

a.

Remove the vinyl tape from the suction pipe sub-assembly and cooler refrigerant liquid pipe A.


b.

Apply sufficient compressor oil to a new 2 O-rings and fitting surface of the suction pipe sub-assembly and cooler refrigerant liquid pipe A.

Compressor Oil:

VC100YF or equivalent



c.

Install the O-ring to the suction pipe sub-assembly and cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-ring and O-ring fitting surface free of foreign matter.



d.

Connect the suction pipe sub-assembly and cooler refrigerant liquid pipe A.


e.

Install the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 28.CONNECT INLET HEATER WATER HOSE

a.
I112532C01
1.76,2.802 1.906,2.594 false 0.135,2.313 0.448,2.51 0.313,0.198 10 false *a 1.917,2.448 2.229,2.646 0.313,0.198 10 false *b 2.365,2.354 2.677,2.552 0.313,0.198 10 false *c 2.063,1.573 2.219,1.771 0.156,0.198 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (135°)


Connect the inlet heater water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the inlet heater water hose.



Hide 87246 29.CONNECT OUTLET HEATER WATER HOSE

a.
I112533C01
1.771,2.792 1.969,2.573 false 0.104,2.24 0.417,2.438 0.313,0.198 10 false *a 1.021,2.229 1.333,2.427 0.313,0.198 10 false *c 1.917,2.396 2.229,2.594 0.313,0.198 10 false *d 0.667,1.073 0.823,1.271 0.156,0.198 10 true A
*a View A
*b Marking (White)
*c Clip Installation Angle (135°)


Connect the outlet heater water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.

NOTICE:

Do not apply excessive force to the outlet heater water hose.



Hide 55701J 30.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 31.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55736D 32.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 33.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55735A 34.INSTALL WATER GUARD PLATE LH

Hide 55737B 35.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 36.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 37.ADD ENGINE COOLANT (for 8NR-FTS)

Hide 38.ADD ENGINE COOLANT (for 3ZR-FAE)

Hide 39.INSPECT FOR COOLANT LEAK (for 8NR-FTS)

Hide 40.INSPECT FOR COOLANT LEAK (for 3ZR-FAE)

Hide 41. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))

Hide 42.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))

Hide 45.INSPECT FOR REFRIGERANT LEAK (for HFC-134a(R134a))

Hide 46.INSPECT FOR REFRIGERANT LEAK (for HFO-1234yf(R1234yf))