Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0293870 CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER A

3ZR-FAE ENGINE CONTROL  CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable valve lift controller assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Memorize steering angle neutral point Simple intelligent parking assist system*1 (Click here)
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Initialize back door lock Power door lock control system (Click here)
Replacement of continuously variable valve lift controller assembly Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 28800 2.REMOVE BATTERY

Hide 17705 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 5.DISCONNECT ENGINE WIRE

a.

Disengage the 10 clamps, and then disconnect the 21 connectors.

A391998C01
4.938,1.802 5.167,1.469 true 2.219,5.958 2.146,5.677 true 1.594,5.854 1.406,5.615 true 5.26,7.135 5.542,6.781 true 2.052,5.479 2.26,5.667 0.208,0.188 10 true *1 4.854,1.833 5.063,2.021 0.208,0.188 10 true *1 1.177,5.49 1.385,5.677 0.208,0.188 10 true *1 5.167,7.146 5.375,7.333 0.208,0.188 10 true *2
*1 Bolt *2 Nut



b.

Remove the 3 bolts and nut, and disconnect the engine wire.


Hide 19500 6.REMOVE IGNITION COIL ASSEMBLY

a.
A393484

Remove the 4 bolts and 4 ignition coil assemblies from the cylinder head cover sub-assembly.


Hide 17650 7.REMOVE PURGE VALVE (PURGE VSV)

a.
A393485

Disconnect the No. 1 fuel vapor feed hose from the intake manifold.


b.
A393486

Slide the clip and disconnect the fuel vapor feed hose from the purge valve (purge VSV).


c.

Remove the 2 bolts and purge valve (purge VSV) from the cylinder head cover sub-assembly.


Hide 11201 8.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 9.REMOVE CYLINDER HEAD COVER GASKET

Hide 222A0 10.REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

a.
A173623

Using a screwdriver, slide the valve lift control actuator connector clip from the valve lift control actuator connector.

NOTICE:

Slide only the upper part of the valve lift control actuator connector clip, as the straight pin will fall out from the bottom if the valve lift control actuator connector clip is completely removed.



b.
A319440C01
0.573,2.344 0.938,2.646 0.365,0.302 10 false *a 1.354,0.198 1.719,0.5 0.365,0.302 10 false *b
*a No. 1 Cylinder
*b No. 3 Cylinder


Rotate the crankshaft clockwise until the intake camshaft position at the No. 1 cylinder and No. 3 cylinder are as shown in the illustration.

HINT:

If the intake camshaft position is not as shown in the illustration, rotate the crankshaft clockwise again so that the intake camshaft is aligned as shown in the illustration.



c.

Turn the crankshaft counterclockwise approximately 10 to 15°.


d.
A319442

Using 2 screwdrivers, lightly pry the valve lift control actuator connector to make a space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly.

NOTICE:
·

Do not forcibly pry the valve lift control actuator connector.

·

Do not damage the camshaft housing sub-assembly and camshaft bearing cap.




e.
A174395

Using a magnet hand, remove the straight pin from the valve lift control actuator connector.

NOTICE:

Do not drop the straight pin into the engine.


HINT:
·

The straight pin can be removed by utilizing the space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly to move the continuously variable valve lift controller assembly so that there is no load on the straight pin.

·

If the straight pin cannot removed easily, slightly turn the crankshaft clockwise and then counterclockwise.




f.
A175190

Using a screwdriver, remove the valve lift control actuator connector clip from the valve lift control actuator connector.

NOTICE:

Do not drop the valve lift control actuator connector clip into the engine.



g.
A173624

Remove the 2 nuts and wire harness clamp bracket from the camshaft housing sub-assembly.


h.

Remove the bolt from the continuously variable valve lift controller assembly.


i.
A207931

Remove the continuously variable valve lift controller assembly from the camshaft housing sub-assembly.

NOTICE:

If the continuously variable valve lift controller assembly has been struck or dropped, replace it.



j.
A320670C04
2,1 2.417,0.427 2.417,0.427 2.583,0.427 false 2.615,0.375 2.958,0.615 0.344,0.24 10 false *1
*1 O-ring


Remove the O-ring from the continuously variable valve lift controller assembly.


k.
A299868

Remove the valve lift control actuator connector from the valve rocker shaft assembly.