12108
1.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.
12108A
2.REMOVE OIL FILLER CAP GASKET
Remove the oil filler cap gasket from the oil filler cap sub-assembly.
3.REMOVE ENGINE COVER JOINT
Remove the 2 engine cover joints.
19100P
4.REMOVE SPARK PLUG
11101E
5.REMOVE CAMSHAFT POSITION SENSOR
for Intake Side:
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL
for Exhaust Side:
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL
11101J
6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
for Intake Side
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>REMOVAL
for Exhaust Side:
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>REMOVAL
11401G
7.REMOVE CRANKSHAFT POSITION SENSOR
83530
8.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
89615
9.REMOVE KNOCK SENSOR
89422
10.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
11201
11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.
Remove the 3 gaskets from the camshaft bearing cap.
As gaskets may stick to the cylinder head cover sub-assembly, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover sub-assembly.
11213
12.REMOVE CYLINDER HEAD COVER GASKET
Remove the cylinder head cover gasket.
11193
13.REMOVE SPARK PLUG TUBE GASKET
Pry up the 4 claws of the ventilation baffle plate.
Do not deform the claws of the ventilation baffle plate more than necessary.
Remove the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.
Be careful not to damage the cylinder head cover sub-assembly.
Prevent the spark plug tube gaskets from being deformed as much as possible. The removed spark plug tube gaskets will be used when installing new spark plug tube gaskets.
14.REMOVE OIL FILTER
15.REMOVE OIL FILTER BRACKET CLIP (for Oil Filter Element Kit Type)
Remove the oil filter bracket clip from the oil filter bracket.
15600A
16.REMOVE OIL FILTER UNION (for Oil Filter Sub-assembly Type)
Using a 12 mm hexagon socket wrench, remove the oil filter union from the oil filter bracket.
17.SET NO. 1 CYLINDER TO TDC/COMPRESSION
| *a | Timing Mark |
| *b | Timing Notch |
Turn the crankshaft pulley until its timing notch and timing mark "0" of the timing chain cover sub-assembly are aligned.
Check that timing marks on both the camshaft timing exhaust gear assembly and camshaft timing gear assembly are facing upward as shown in the illustration.
If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.
13471
18.REMOVE CRANKSHAFT PULLEY
13540
19.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.
Do not turn the crankshaft without the No. 1 chain tensioner assembly installed.
11302
20.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
11302A
21.REMOVE TIMING CHAIN COVER OIL SEAL
16323
22.REMOVE WATER INLET HOUSING
Remove the 3 bolts, water inlet housing and gasket.
12511
23.REMOVE NO. 1 GENERATOR BRACKET
Remove the 4 bolts and No. 1 generator bracket.
13559
24.REMOVE CHAIN TENSIONER SLIPPER
Remove the chain tensioner slipper from the cylinder block sub-assembly.
13561
25.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
13506
26.REMOVE CHAIN SUB-ASSEMBLY
Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and camshaft timing gear assembly.
With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear assembly and place it on the camshaft timing gear assembly.
Be sure to release the chain sub-assembly from the sprocket completely.
Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.
13521
27.REMOVE CRANKSHAFT TIMING SPROCKET
13507
28.REMOVE NO. 2 CHAIN SUB-ASSEMBLY
19315
29.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
Remove the No. 1 crankshaft position sensor plate.
13521A
30.REMOVE CRANKSHAFT TIMING GEAR KEY
| *a | Protective Tape |
Using a screwdriver, remove the 2 crankshaft timing gear keys.
Tape the screwdriver tip before use.
13050
31.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
13070A
32.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13050
33.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
13070A
34.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
13908
35.REMOVE VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY
13908
36.INSTALL VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY
11103
37.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
222A0
38.REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY
13801
39.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 16 No. 1 valve rocker arm sub-assemblies.
Arrange the removed parts in the correct order.
13750
40.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 16 valve lash adjuster assemblies.
Arrange the removed parts in the correct order.
13716
41.REMOVE VALVE STEM CAP
Remove the 16 valve stem caps.
Arrange the removed parts in the correct order.
11101
42.REMOVE CYLINDER HEAD SUB-ASSEMBLY
11114A
43.REMOVE CAMSHAFT HOUSING STRAIGHT PIN
It is not necessary to remove a camshaft housing straight pin unless it is being replaced.
11115
44.REMOVE CYLINDER HEAD GASKET
12204
45.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
12101A
46.REMOVE OIL PAN DRAIN PLUG
Remove the oil pan drain plug and gasket.
12102A
47.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
15100
48.REMOVE OIL PUMP ASSEMBLY
11401L
49.REMOVE REAR ENGINE OIL SEAL
11420
50.REMOVE STIFFENING CRANKCASE ASSEMBLY
Uniformly loosen and remove the 11 bolts.
| *a | Protective Tape |
Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly.
Be careful not to damage the contact surfaces of the stiffening crankcase assembly and cylinder block sub-assembly.
Tape the screwdriver tip before use.
11432A
51.REMOVE NO. 1 TAPER SCREW PLUG
Remove the 2 No. 1 taper screw plugs.
52.REMOVE STUD BOLT
If a stud bolt is deformed or its threads are damaged, replace it.
53.REMOVE STIFFENING CRANKCASE RING PIN
It is not necessary to remove a stiffening crankcase ring pin unless it is being replaced.