Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL PUMP (for AWD) › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293905 FUEL PUMP(for AWD) A

8NR-FTS FUEL  FUEL PUMP(for AWD)  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.

Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.
A393051C01
0.271,2.667 0.938,2.667 true 1.083,1.094 2.667,0.333 true 2.438,1.219 2.667,0.333 true 2.667,0.135 2.854,0.323 0.188,0.188 10 true *a 0.063,2.552 0.375,2.708 0.313,0.156 10 false *a
*a Protrusion
V100135

Notch


Align the protrusions of the fuel suction tube with pump and gauge assembly with the notches in the fuel tank assembly.


Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Install the fuel pump gauge retainer.

i.

While pressing down on the fuel suction tube with pump and gauge assembly, temporarily install the fuel pump gauge retainer.


ii.
A393052C01
0.844,3.104 1.677,3.104 true 2.063,2.115 2.063,1.698 true 2.083,1.25 2.833,1.25 true 2.677,0.583 2.917,0.583 true 0.969,0.333 1.542,0.333 true 1.719,2.99 2.031,3.146 0.313,0.156 10 false *a 2.927,0.479 3.135,0.677 0.208,0.198 10 true *b 1.979,2.135 2.24,2.344 0.26,0.208 10 false *c 2.854,1.146 3.063,1.333 0.208,0.188 10 true *d 0.76,0.219 0.969,0.406 0.208,0.188 10 true *d
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



iii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iv.
A393053C01
2.083,0.885 2.5,0.667 true 0.833,1.75 1.083,1.25 true 2.167,1.344 2.563,1.146 true 0.5,1.125 0.865,1.323 true 1.917,0.417 1.417,0.604 true 1.135,3.833 1.667,3.833 true 0.333,3.458 0.583,3.583 true 1.729,3.719 1.927,3.927 0.198,0.208 10 true *a 0.115,3.323 0.313,3.521 0.198,0.198 10 true *b 2,0.302 2.198,0.5 0.198,0.198 10 true *c 0.26,1.021 0.458,1.198 0.198,0.177 10 true *d 2.667,0.99 2.865,1.188 0.198,0.198 10 true *e 0.667,1.833 0.844,2.01 0.177,0.177 10 true *f 2.573,0.5 2.75,0.677 0.177,0.177 10 true *f
*a Triangle Mark (Fuel Pump Gauge Retainer)
*b Triangle Mark (Fuel Tank Assembly)
*c SST (Handle)
*d SST (Plate)
*e SST (Claw)
*f SST (Bolt)
V100136

Front Side of Vehicle


Install SST (handle) to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


v.

Using SST, rotate the fuel pump gauge retainer so that the triangle mark on the fuel pump gauge retainer are aligned with the triangle mark on the fuel tank assembly to install the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

·

Make sure that the fuel suction tube set gasket does not come off.





b.

Engage the claw to install the No. 1 fuel tube clamp.


Hide 77754B 3.CONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A395459C01
1.052,2.188 1.26,2.375 0.208,0.188 10 false *a 1.74,2.188 1.948,2.375 0.208,0.188 10 false *b
*a 180°
*b Top of Vehicle


Connect the charcoal canister outlet hose to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.

HINT:

Engage the clip within the area shown in the illustration.



Hide 77026A 4.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel evaporation tube sub-assembly to the fuel suction tube with pump and gauge assembly and slide the clip to secure it.


Hide 77209F 5.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

A393054C01
5.417,1.417 6.417,2.667 1,1.25 3.833,1.417 4.833,2.667 1,1.25 2.333,1.885 2.333,1.469 true 3.01,1.333 3.344,1.333 false 5.323,0.333 5.656,0.333 false 5.531,0.625 5.865,0.625 false 5.323,0.885 5.906,0.885 true 5.323,0.76 5.74,0.76 5.74,0.76 5.74,0.875 true 4.583,1.031 4.583,0.781 false 5.885,1.917 6.083,1.667 true 4.5,2.333 4.25,2 true 4.49,1.073 4.802,1.229 0.313,0.156 10 false *1 3.385,1.24 3.698,1.396 0.313,0.156 10 false *2 2.25,1.938 2.438,2.125 0.188,0.188 10 true *3 5.698,0.229 6.01,0.385 0.313,0.156 10 false *a 5.948,0.781 6.26,0.938 0.313,0.156 10 false *b 3.875,1.458 4.188,1.615 0.313,0.156 10 false *c 5.458,1.458 5.771,1.615 0.313,0.156 10 false *d 5.906,0.531 6.219,0.688 0.313,0.156 10 false *2 4.552,2.292 4.865,2.448 0.313,0.156 10 false *e 6.073,1.51 6.385,1.667 0.313,0.156 10 false *e
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly - -
*a Fuel Tube Joint *b O-ring
*c Correct *d Incorrect
*e Collar - -
V100135

Insert
V100136

Insert


NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 6.CONNECT FUEL TANK EVAPORATION VENT TUBE SUB-ASSEMBLY

a.

Connect the fuel tank evaporation vent tube sub-assembly to the fuel suction tube with pump and gauge assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 58325E 7.INSTALL REAR FLOOR SERVICE HOLE COVER LH

a.

Remove any remaining butyl tape from the rear floor service hole cover LH and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover LH and vehicle body.


c.

Connect the fuel suction tube with pump and gauge assembly connector.


d.

Install the rear floor service hole cover LH with new butyl tape.


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 10.INSTALL REAR SEAT ASSEMBLY

Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION