The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator.
The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger without door airbag assembly.
DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1660/43 | Passenger Airbag ON/OFF Indicator Circuit Malfunction | Any of the following conditions is met:
·
The airbag sensor assembly detects a line short in the passenger airbag ON/OFF indicator circuit. ·
The airbag sensor assembly detects a short to ground in the passenger airbag ON/OFF indicator circuit. ·
The airbag sensor assembly detects a short to B+ in the passenger airbag ON/OFF indicator circuit. ·
The airbag sensor assembly detects an open in the passenger airbag ON/OFF indicator circuit. ·
Passenger airbag ON/OFF indicator malfunction ·
Airbag sensor assembly malfunction |
·
Instrument panel wire ·
Instrument panel junction block assembly ·
Passenger airbag ON/OFF indicator (Clock assembly) ·
Airbag sensor assembly |
Does not apply to test/check mode |
| Vehicle Condition | |||||||
|---|---|---|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | Pattern 4 | Pattern 5 | Pattern 6 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ | ○ | ○ | ○ | ○ |
| Malfunction Status | The airbag sensor assembly detects a line short in the passenger airbag ON/OFF indicator circuit | ○ | - | - | - | - | - |
| The airbag sensor assembly detects a short to ground in the passenger airbag ON/OFF indicator circuit | - | ○ | - | - | - | - | |
| The airbag sensor assembly detects a short to B+ in the passenger airbag ON/OFF indicator circuit | - | - | ○ | - | - | - | |
| The airbag sensor assembly detects an open in the passenger airbag ON/OFF indicator circuit | - | - | - | ○ | - | - | |
| Passenger airbag ON/OFF indicator malfunction | - | - | - | - | ○ | - | |
| Airbag sensor assembly malfunction | - | - | - | - | - | ○ | |
| Detection Time | - | - | - | - | - | - | |
| Number of Trips | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Inspect the fuses for circuits related to this system before performing the following procedure.
Turn the ignition switch ON.
Check the passenger airbag ON/OFF indicator operation.
Refer to the normal condition of the passenger airbag ON/OFF indicator.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| Passenger airbag ON/OFF indicator illumination is always on. | A |
| Passenger airbag ON/OFF indicator illumination is always off. | B |
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.
Check the passenger airbag ON/OFF indicator operation.
The passenger airbag ON/OFF indicator does not come on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/o Dual-stage SRS |
| *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator (Clock Assembly) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Connect the connector to the airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1660/43 is not output.
Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Turn the ignition switch off.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect the connector from the passenger airbag ON/OFF indicator (clock assembly).
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - F81-3 (P-AB) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the service wire from connector B.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - F81-3 (P-AB) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
- | - |
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - Body ground | ignition switch ON | Below 1 V |
| F81-3 (P-AB) - Body ground | ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - Body ground | Always | 1 MΩ or higher |
| F81-3 (P-AB) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - Body ground | Always | 1 MΩ or higher |
| 3A-29 (PAON) - Body ground | Always | 1 MΩ or higher |
| 3A-46 (P-AB) - Body ground | Always | 1 MΩ or higher |
| 3A-51 (P-AB) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| 3A-29 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| 3A-46 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
| 3A-51 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - 3A-46 (P-AB) | Always | 1 MΩ or higher |
| 3A-29 (PAON) - 3A-51 (P-AB) | Always | 1 MΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
*b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - 3A-46 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Using a service wire, connect terminals 3 (PAON) and 4 (P-AB) of connector E.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
*b | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-29 (PAON) - 3A-51 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.
The connectors are properly connected.
If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.
Check that the terminals of the connectors are not deformed or damaged.
The terminals are not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
*b | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - F81-3 (P-AB) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the service wire from connector B.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - F81-3 (P-AB) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
- | - |
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| F81-3 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F81-4 (PAON) - Body ground | Always | 1 MΩ or higher |
| F81-3 (P-AB) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the cable to the negative (-) battery terminal.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator (Clock Assembly) | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector (to Passenger Airbag ON/OFF Indicator (Clock Assembly)) | - | - |
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F81-7 (B) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the connector to the passenger airbag ON/OFF indicator (clock assembly).
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator (Clock Assembly) | *4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
- | - |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.
Check the passenger airbag ON/OFF indicator according to the conditions in the table below.
| Terminal Connection | Switch Condition | Specified Condition |
|---|---|---|
| F70-23 (PAON) - Body ground | Ignition switch ON | "ON" comes on |
| F70-17 (P-AB) - Body ground | Ignition switch ON | "OFF" comes on |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *A | w/o Dual-stage SRS |
| *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator (Clock Assembly) |
Connect the connector to the airbag sensor assembly.
Connect the cable to the negative (-) battery terminal.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1660/43 is not output.
Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - Body ground | Always | 1 MΩ or higher |
| 3A-29 (PAON) - Body ground | Always | 1 MΩ or higher |
| 3A-46 (P-AB) - Body ground | Always | 1 MΩ or higher |
| 3A-51 (P-AB) - Body ground | Always | 1 MΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| 3A-29 (PAON) - Body ground | Ignition switch ON | Below 1 V |
| 3A-46 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
| 3A-51 (P-AB) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - 3A-46 (P-AB) | Always | 1 MΩ or higher |
| 3A-29 (PAON) - 3A-51 (P-AB) | Always | 1 MΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the connector from the instrument panel junction block assembly.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
*b | Front view of wire harness connector
(to Airbag Sensor Assembly) |
The service wire has already been inserted into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-8 (PAON) - 3A-46 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Using a service wire, connect terminals 3 (PAON) and 4 (P-AB) of connector E.
| *A | w/o Dual-stage SRS | *B | w/ Dual-stage SRS |
| *1 | Instrument Panel Junction Block Assembly | *2 | Airbag Sensor Assembly |
| *3 | Passenger Airbag ON/OFF Indicator
(Clock Assembly) |
*4 | Instrument Panel Wire |
| *5 | Service Wire | - | - |
| *a | Front view of wire harness connector
(to Instrument Panel Junction Block Assembly) |
*b | Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly)) |
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-29 (PAON) - 3A-51 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector E.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C