Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292533 MANUAL TRANSAXLE SYSTEM C

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  P080512  Clutch Position Sensor "A"Circuit Short to Battery  P080514  Clutch Position Sensor "A"Circuit Short to Ground or Open  


DESCRIPTION

The clutch pedal stroke sensor assembly is mounted on the clutch pedal and detect the clutch pedal position and send signals to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P080512 Clutch Position Sensor "A"Circuit Short to Battery Clutch stroke sensor signal voltage is 4.8 V or more for 0.5 seconds or more (1 trip detection logic)
·

Clutch pedal stroke sensor assembly

·

Open or short in clutch stroke sensor circuit

·

ECM


Does not come on DTC stored SAE Code:
P0808
P080514 Clutch Position Sensor "A"Circuit Short to Ground or Open Clutch stroke sensor signal voltage is 0.2 V or less for 0.5 seconds or more (1 trip detection logic)
·

Clutch pedal stroke sensor assembly

·

Open or short in clutch stroke sensor circuit

·

ECM


Does not come on DTC stored SAE Code:
P0807

WIRING DIAGRAM

C364959E02
0.927,3.677 3.99,3.875 3.063,0.198 10 false Clutch Pedal Stroke Sensor Assembly 0.938,3.438 1.396,3.635 0.458,0.198 10 false A47 5.344,4.052 5.802,4.25 0.458,0.198 10 false C62 5.344,4.26 5.802,4.458 0.458,0.198 10 false ECM 5.177,1.833 5.792,2.031 0.615,0.198 10 false VCCL 5.177,2.292 5.635,2.49 0.458,0.198 10 false CLS 5.177,2.75 5.792,2.948 0.615,0.198 10 false E2CL 5.927,1.667 6.385,1.865 0.458,0.198 10 false 5 V 1.844,1.833 2.302,2.031 0.458,0.198 10 false VDD 1.833,2.292 2.292,2.49 0.458,0.198 10 false OUT 1.833,2.74 2.292,2.938 0.458,0.198 10 false GND 4.844,1.833 5.156,2.031 0.313,0.198 10 false 89 4.771,2.292 5.229,2.49 0.458,0.198 10 false 119 4.844,2.74 5.156,2.938 0.313,0.198 10 false 87 2.271,1.833 2.427,2.031 0.156,0.198 10 false 3 2.271,2.292 2.427,2.49 0.156,0.198 10 false 2 2.26,2.74 2.417,2.938 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.

Click hereDrivetrain>EC6A (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (1) again.



PROCEDURE

1.READ VALUE USING GTS (CLUTCH STROKE SENSOR VOLTAGE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmison / Data List / Clutch Stroke Sensor Voltage.

Powertrain > Transmission > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 373 607

e.

Read the values displayed on the GTS.

Standard Voltage:
GTS Display Condition Specified Condition
CLUTCH STROKE SENSOR VOLTAGE Clutch pedal fully released 0.5 to 1.1 V
Clutch pedal fully depressed 2.6 to 4.5 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CLUTCH PEDAL STROKE SENSOR ASSEMBLY)
a.
C364961C01
1.417,0.177 1.917,0.417 0.5,0.24 1.406,1.104 1.083,1.667 true 1.667,1.094 2.167,1.667 true 1.552,0.24 2.01,0.438 0.458,0.198 10 false A47 0.75,1.604 1.208,1.802 0.458,0.198 10 false GND 2.24,1.625 2.698,1.823 0.458,0.198 10 false VDD 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Clutch Pedal Stroke Sensor Assembly)


Disconnect the clutch pedal stroke sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A47-3 (VDD) - A47-1 (GND) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
a.

Disconnect the C62 ECM connector.


b.

Disconnect the A47 clutch pedal stroke sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-2 (OUT) - C62-119 (CLS) Always Below 1 Ω
C62-119 (CLS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE CLUTCH PEDAL STROKE SENSOR ASSEMBLY
a.

Replace the clutch pedal stroke sensor assembly.



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P080512 OR P080514)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P080512 OR P080514)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Transmission > Clear DTCs
50002 373

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Transmison / Trouble Codes.

Powertrain > Transmission > Trouble Codes
50001 373

i.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P080512 or P080514 is output B



A

END

B

6.REPLACE ECM
6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CHECK HARNESS AND CONNECTOR (CLUTCH PEDAL STROKE SENSOR ASSEMBLY - ECM)
a.

Disconnect the C62 ECM connector.


b.

Disconnect the A47 clutch pedal stroke sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A47-1 (GND) - C62-87 (E2CL) Always Below 1 Ω
A47-3 (VDD) - C62-89 (VCCL) Always Below 1 Ω
C62-87 (E2CL) - Body ground Always 10 kΩ or higher
C62-89 (VCCL) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT