Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1330  Open in Front Speed Sensor RH  C1331  Open in Front Speed Sensor LH  C1332  Open in Rear Speed Sensor RH  C1333  Open in Rear Speed Sensor LH  C1464  Front Speed Sensor RH  C1465  Front Speed Sensor LH  C1466  Rear Speed Sensor RH  C1467  Rear Speed Sensor LH  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU (brake actuator assembly). These signals are used by the ABS.

HINT:

The output voltage values shown below are for when the vehicle wire harnesses are connected to the skid control ECU (brake actuator assembly) and the speed sensors.


C121324C03
2,1.302 2.26,1.073 false 1.948,3.333 2.083,2.833 true 0.719,0.188 1.469,0.385 0.75,0.198 12 false *B 0.385,0.188 1.135,0.385 0.75,0.198 12 false *A 1.865,4.5 2.083,4.677 0.219,0.177 10 false *2 1.823,2.135 2.042,2.302 0.219,0.167 10 false *2 2.146,2.729 3.104,2.927 0.958,0.198 10 false *1 2.292,1 3.25,1.198 0.958,0.198 10 false *1 6.438,1.802 6.896,2 0.458,0.198 10 false 0.3 V 6.427,2.208 6.948,2.438 0.521,0.229 10 false 0.15 V 5.594,2.625 5.792,2.813 0.198,0.188 10 false *c 4.677,2.635 4.979,2.823 0.302,0.188 10 false *b 5.229,1.365 5.542,1.563 0.313,0.198 10 false *a 0.417,2.771 1.167,2.969 0.75,0.198 12 false *C
*A for Front *B for Rear AWD
*C for Rear 2WD - -
*1 Speed Sensor *2 Speed Sensor Rotor
*a Waveform (Reference): Between Speed Sensor (-) and Body Ground *b Low speed
*c High speed - -


DTC No. Detection Item DTC Detection Condition Trouble Area
C1330 Open in Front Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Front speed sensor RH

·

Speed sensor circuit

·

Sensor installation


C1331 Open in Front Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Front speed sensor LH

·

Speed sensor circuit

·

Sensor installation


C1332 Open in Rear Speed Sensor RH An open or short in the speed sensor signal circuit.
·

Rear speed sensor RH (rear axle hub and bearing assembly RH)*1

·

Rear speed sensor RH*2

·

Speed sensor circuit

·

Sensor installation


C1333 Open in Rear Speed Sensor LH An open or short in the speed sensor signal circuit.
·

Rear speed sensor LH (rear axle hub and bearing assembly RH)*1

·

Rear speed sensor LH*2

·

Speed sensor circuit

·

Sensor installation


C1464 Front Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.08 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor RH

·

Speed sensor circuit

·

Front speed sensor rotor RH (front axle hub sub-assembly RH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)


C1465 Front Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input for 0.08 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a front wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Front speed sensor LH

·

Speed sensor circuit

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)


C1466 Rear Speed Sensor RH Any of the following is detected:
1.

The vehicle speed is more than 43.2 km/h (27 mph) and pulses are not input for 0.08 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor RH (rear axle hub and bearing assembly RH)*1

·

Rear speed sensor RH*2

·

Speed sensor circuit

·

Rear speed sensor rotor RH (rear axle hub and bearing assembly RH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)


C1467 Rear Speed Sensor LH Any of the following is detected:
1.

The vehicle speed is more than 43.2 km/h (27 mph) and pulses are not input for 0.08 seconds.

2.

After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected.

3.

After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected.

4.

The following conditions are met for 9 to 72 seconds or more (varies depending on the driving conditions):

-

The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)

-

The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.)

-

The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.)


5.

Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less.

6.

An abnormal signal is received from a wheel speed sensor.


·

Rear speed sensor LH (rear axle hub and bearing assembly RH)*1

·

Rear speed sensor LH*2

·

Speed sensor circuit

·

Rear speed sensor rotor LH (rear axle hub and bearing assembly LH)

·

Sensor installation

·

Skid control ECU (brake actuator assembly)



*1: for 2WD

*2: for AWD


DTC Detection Conditions: C1464
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input. ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected. - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.08 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1464
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1465
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is more than 50.4 km/h (31 mph) and pulses are not input. ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected. - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.08 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1465
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1466
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is more than 43.2 km/h (27 mph) and pulses are not input. ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected. - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.08 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1466
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1467
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is more than 43.2 km/h (27 mph) and pulses are not input. ○ - - -
After the initial start or restart and when the vehicle speed has reached 12 km/h (7 mph), a wheel speed of 0 km/h (0 mph) is detected. - ○ - -
After the initial start or restart and when the vehicle speed has reached 20 km/h (12 mph), a rear wheel speed of 0 km/h (0 mph) is detected. - - ○ -
The difference between the speed of the fastest wheel and the speed of the slowest wheel is 5% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - - - ○
Detection Time 0.08 seconds - - 9 to 72 seconds or more (varies depending on the driving conditions)
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


DTC Detection Conditions: C1467
Vehicle Condition
Pattern 5 Pattern 6 Pattern 7 Pattern 8
Diagnosis Condition - - - - -
Malfunction Status The vehicle speed is less than 100 km/h (62 mph) and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6 km/h (4 mph) or more. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 16 km/h (10 mph) is allowable.) ○ - - -
The vehicle speed is 100 km/h (62 mph) or more and the difference between the speed of the fastest wheel and the speed of the slowest wheel is 6% or more of vehicle speed. (If the speed of any wheel is less than 5 km/h (3 mph), a speed difference of up to 15% is allowable.) - ○ - -
Wheel speed sensor signal fluctuation is equivalent to 98 G or more, or alternates between 50 G or more and -50 G or less. - - ○ -
An abnormal signal is received from a wheel speed sensor. - - - ○
Detection Time 9 to 72 seconds or more (varies depending on the driving conditions) 9 to 72 seconds or more (varies depending on the driving conditions) - -
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C243493E90
1.177,1.094 1.302,1.25 0.125,0.156 10 false 1 2.344,1.094 2.469,1.25 0.125,0.156 10 false 2 1.042,1.479 1.375,1.74 0.333,0.26 10 false A25 1.063,3.729 2.635,3.979 1.573,0.25 10 false Front Speed Sensor LH 5.479,4.042 7.042,4.406 1.563,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 5.708,0.594 5.906,0.76 0.198,0.167 10 false 21 5.708,1.156 5.885,1.323 0.177,0.167 10 false 26 5.698,2.583 5.896,2.75 0.198,0.167 10 false 24 5.76,3.167 5.958,3.333 0.198,0.167 10 false 7 5.479,3.865 5.854,4.063 0.375,0.198 10 false A42 5.99,0.635 6.313,0.792 0.323,0.156 10 false FR+ 5.99,1.198 6.313,1.354 0.323,0.156 10 false FR- 5.99,2.677 6.313,2.833 0.323,0.156 10 false FL+ 5.99,3.24 6.313,3.396 0.323,0.156 10 false FL- 1.042,1.646 2.615,1.896 1.573,0.25 10 false Front Speed Sensor RH 1.073,3.563 1.427,3.823 0.354,0.26 10 false A13 1.177,3.146 1.302,3.302 0.125,0.156 10 false 1 2.344,3.146 2.469,3.302 0.125,0.156 10 false 2 1.354,3.24 1.677,3.396 0.323,0.156 10 false FL+ 2,3.24 2.323,3.396 0.323,0.156 10 false FL- 1.354,1.198 1.677,1.354 0.323,0.156 10 false FR+ 2,1.198 2.323,1.354 0.323,0.156 10 false FR-

C266976E42
0.781,0.604 1.104,0.802 0.323,0.198 10 false RR+ 0.792,1.198 1.115,1.396 0.323,0.198 10 false RR- 1.229,0.625 1.458,0.813 0.229,0.188 10 false d1 1.542,0.594 1.865,0.792 0.323,0.198 10 false RR+ 1.969,0.594 2.292,0.792 0.323,0.198 10 false RR+ 1.552,1.208 1.875,1.406 0.323,0.198 10 false RR- 1.979,1.208 2.302,1.406 0.323,0.198 10 false RR- 2.344,0.625 2.667,0.823 0.323,0.198 10 false dM1 2.344,1.208 2.667,1.406 0.323,0.198 10 false dM1 1.26,0.417 1.49,0.604 0.229,0.188 10 false 2 2.427,1 2.656,1.188 0.229,0.188 10 false 2 1.26,1.01 1.49,1.198 0.229,0.188 10 false 1 1.219,1.198 1.448,1.385 0.229,0.188 10 false d1 2.417,0.417 2.646,0.604 0.229,0.188 10 false 1 0.354,1.604 1.094,1.938 0.74,0.333 10 false Rear Speed Sensor RH 1.51,1.615 3.729,2.031 2.219,0.417 10 false Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly) 5.969,0.615 6.292,0.813 0.323,0.198 10 false RR+ 5.979,1.188 6.302,1.385 0.323,0.198 10 false RR- 5.677,0.531 5.906,0.719 0.229,0.188 10 false 22 5.688,1.104 5.917,1.292 0.229,0.188 10 false 37 0.792,2.646 1.115,2.844 0.323,0.198 10 false RL+ 0.823,3.229 1.146,3.427 0.323,0.198 10 false RL- 1.271,2.448 1.5,2.635 0.229,0.188 10 false 2 2.438,3 2.667,3.188 0.229,0.188 10 false 2 1.26,3.031 1.49,3.219 0.229,0.188 10 false 1 2.438,2.438 2.667,2.625 0.229,0.188 10 false 1 1.219,2.646 1.448,2.833 0.229,0.188 10 false e1 1.219,3.229 1.448,3.417 0.229,0.188 10 false e1 2.344,2.635 2.698,2.844 0.354,0.208 10 false eM1 2.333,3.219 2.688,3.427 0.354,0.208 10 false eM1 0.365,3.635 1.104,3.969 0.74,0.333 10 false Rear Speed Sensor LH 1.542,2.646 1.865,2.844 0.323,0.198 10 false RL+ 1.969,2.646 2.292,2.844 0.323,0.198 10 false RL+ 1.552,3.229 1.875,3.427 0.323,0.198 10 false RL- 2,3.219 2.323,3.417 0.323,0.198 10 false RL- 1.51,3.646 3.719,4.052 2.208,0.406 10 false Skid Control Sensor Wire RH (No. 2 Parking Brake Wire Assembly) 5.708,2.563 5.938,2.75 0.229,0.188 10 false 39 5.708,3.115 5.938,3.302 0.229,0.188 10 false 23 5.969,2.635 6.292,2.833 0.323,0.198 10 false RL+ 5.969,3.219 6.292,3.417 0.323,0.198 10 false RL- 5.469,4.115 7.052,4.458 1.583,0.344 10 false Skid Control ECU (Brake Actuator Assembly) 5.51,3.948 5.906,4.135 0.396,0.188 10 false A42

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.RECONFIRM DTC
a.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1330 and/or C1464 are output. A
DTCs C1331 and/or C1465 are output. B
DTCs C1332 and/or C1466 are output (for 2WD). C
DTCs C1333 and/or C1467 are output (for 2WD). D
DTCs C1332 and/or C1466 are output (for AWD). E
DTCs C1333 and/or C1467 are output (for AWD). F



A

2.CHECK FRONT SPEED SENSOR RH INSTALLATION

B

9.CHECK FRONT SPEED SENSOR LH INSTALLATION

C

16.CHECK REAR SPEED SENSOR RH INSTALLATION

D

23.CHECK REAR SPEED SENSOR LH INSTALLATION

E

30.CHECK REAR SPEED SENSOR RH INSTALLATION

F

39.CHECK REAR SPEED SENSOR LH INSTALLATION
2.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle RH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

3.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

4.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR RH

4.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375627C05
0.333,0.813 0.75,1.125 0.417,0.313 1.875,0.823 2.521,1.135 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.427,0.906 0.885,1.104 0.458,0.198 10 false A25 2.625,1.104 3.083,1.302 0.458,0.198 10 false FR+
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A25 front speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A25-1 (FR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
5.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375627C06
0.281,0.844 0.688,1.115 0.406,0.271 1.094,1.542 1.531,0.854 true 2.24,1.552 1.875,0.854 true 0.073,0.198 0.385,0.396 0.313,0.198 10 false *a 0.375,0.917 0.833,1.115 0.458,0.198 10 false A25 2.156,1.604 2.615,1.802 0.458,0.198 10 false FR+ 1,1.604 1.458,1.802 0.458,0.198 10 false FR-
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A25-1 (FR+) - A25-2 (FR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
6.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor rotor (front axle hub assembly RH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor is incorporated into the front axle hub assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub assembly.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH

C

CLEAN FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH)

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-26 (FR-) - A25-2 (FR-) Always Below 1 Ω
A42-26 (FR-) or A25-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-26 (FR-) - A25-2 (FR-) Always Below 1 Ω
A42-26 (FR-) or A25-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK FRONT SPEED SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

10.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR LH

10.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

11.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR LH

11.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375627C07
0.333,0.813 0.75,1.125 0.417,0.313 1.875,0.823 2.521,1.135 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.427,0.906 0.885,1.104 0.458,0.198 10 false A13 2.625,1.104 3.083,1.302 0.458,0.198 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor LH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A13 front speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-1 (FL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

12.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

14.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
12.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375627C08
0.281,0.844 0.688,1.115 0.406,0.271 1.094,1.542 1.531,0.854 true 2.24,1.552 1.875,0.854 true 0.073,0.198 0.385,0.396 0.313,0.198 10 false *a 0.375,0.917 0.833,1.115 0.458,0.198 10 false A13 2.156,1.604 2.615,1.802 0.458,0.198 10 false FL+ 1,1.604 1.458,1.802 0.458,0.198 10 false FL-
*a Front view of wire harness connector
(to Front Speed Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-1 (FL+) - A13-2 (FL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)

NG

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
13.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor rotor (front axle hub assembly LH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor is incorporated into the front axle hub assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub assembly.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH

C

CLEAN FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH)

14.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-7 (FL-) - A13-2 (FL-) Always Below 1 Ω
A42-7 (FL-) or A13-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-7 (FL-) - A13-2 (FL-) Always Below 1 Ω
A42-7 (FL-) or A13-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor RH
*a OK
*b NG
*c No Clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly RH cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

17.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

17.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C05
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false d1 2.438,1.781 2.781,2 0.344,0.219 10 false RR+
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the d1 rear speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

19.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
18.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C06
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false d1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RR+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RR-
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - d1-1 (RR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

21.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
19.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

20.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

22.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

22.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor LH
*a OK
*b NG
*c No Clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly LH cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

24.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

24.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C07
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false e1 2.438,1.781 2.781,2 0.344,0.219 10 false RL+
*a Front view of wire harness connector
(to Rear Speed Sensor LH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the e1 rear speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

25.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

26.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
25.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C08
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false e1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RL+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RL-
*a Front view of wire harness connector
(to Rear Speed Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - e1-1 (RL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

28.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
26.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

27.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

29.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier sub-assembly RH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

31.CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR RH

31.CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

32.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE REAR SPEED SENSOR RH

32.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C05
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false d1 2.438,1.781 2.781,2 0.344,0.219 10 false RR+
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the d1 rear speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

33.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

35.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
33.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C06
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false d1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RR+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RR-
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - d1-1 (RR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

34.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)

NG

37.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
34.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)
a.

Remove the rear speed sensor rotor (rear axle hub and bearing assembly RH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly RH.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

C

CLEAN REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY RH)

35.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

36.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

36.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

38.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier sub-assembly LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

40.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR RH

40.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

41.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH

41.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C07
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false e1 2.438,1.781 2.781,2 0.344,0.219 10 false RL+
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the e1 rear speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

42.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

44.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
42.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C08
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false e1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RL+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RL-
*a Front view of wire harness connector
(to Rear Speed Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - e1-1 (RL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

43.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)

NG

46.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
43.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)
a.

Remove the rear speed sensor rotor (rear axle hub and bearing assembly LH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly LH.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

C

CLEAN REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY LH)

44.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

45.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

45.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

46.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

47.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

47.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR