Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2016.10–2019.09
RM32H0E _54 Brake _060043 PARKING BRAKE _0294919 ELECTRIC PARKING BRAKE SYSTEM J

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  Electric Parking Brake System AUTO Function Circuit  


DESCRIPTION

for Continuously Variable Transaxle:

The skid control ECU (brake actuator assembly) receives shift position information from the ECM via CAN communication.

In addition, front seat inner belt information and driver seat door courtesy switch information is received from the main body ECU (multiplex network body ECU).

The electric parking brake system AUTO function (shift-linked function) automatically releases the parking brake when the following conditions are met: 1) Ignition switch to ON, 2) brake pedal is depressed, and 3) shift lever is moved out of P. When the shift lever is moved to P with these conditions met, the function automatically locks the parking brake.

The electric parking brake system AUTO (shift-linked function) automatically engages the parking brake when the shift lever is moved to P and disengages the parking brake when the shift lever is moved out of P when the ignition switch to ON and the brake pedal is depressed.

for Manual Transaxle:

The skid control ECU (brake actuator assembly) receives clutch stroke information from the ECM and neutral position information from the engine stop and start ECU (w/ Stop and Start System) via CAN communication.

In addition, front seat inner belt information and driver seat door courtesy switch information is received from the main body ECU (multiplex network body ECU).

The AUTO function (ignition switch-linked function) of the electric parking brake system automatically locks when the ignition switch is turned off.

WIRING DIAGRAM

C367785E01
2,1.854 2.406,2.042 0.406,0.188 10 false SWI1 1.938,2.167 2.396,2.365 0.458,0.198 10 false SWO1 2.021,2.469 2.417,2.625 0.396,0.156 10 false SWI2 1.958,3.063 2.458,3.24 0.5,0.177 10 false SWO2 0.104,3.594 2.49,4 2.385,0.406 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 3.156,1.958 3.563,2.146 0.406,0.188 10 false SWI1 3.156,2.25 3.615,2.448 0.458,0.198 10 false SWO1 3.156,2.552 3.552,2.708 0.396,0.156 10 false SWI2 3.167,3.135 3.667,3.313 0.5,0.177 10 false SWO2 5.771,1.281 6.177,1.469 0.406,0.188 10 false ECM 5.073,2.5 6.906,2.708 1.833,0.208 10 false Combination Meter Assembly 4.958,3.708 7.135,4.052 2.177,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 5.063,5.031 6.917,5.24 1.854,0.208 10 false Engine Stop and Start ECU*1 2.135,4.917 4.906,5.125 2.771,0.208 10 false Skid Control ECU (Brake Actuator Assembly) 1.323,5.146 3.021,5.354 1.698,0.208 10 false : CAN Communication Line 5.073,5.354 6.927,5.563 1.854,0.208 10 false *1: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned to ON.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (AUTO MODE)

B

2.READ VALUE USING GTS (AUTO MODE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Auto Mode AUTO mode permission status ON or OFF OFF: Manual mode
ON: AUTO mode
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Auto Mode
50003 105 465

g.

When switching the mode, check that the Data List display turns on and off.


Result:
Result Proceed to
The Data List display does not turn on and off according to mode switching A
The Data List display turns on and off according to mode switching (for CVT) B
The Data List display turns on and off according to mode switching (for Manual Transaxle with Stop and Start System) C
The Data List display turns on and off according to mode switching (for Manual Transaxle without Stop and Start System) D



A

3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

B

5.READ VALUE USING GTS (SHIFT POSITION)

C

7.READ VALUE USING GTS (NEUTRAL SWITCH)

D

10.READ VALUE USING GTS (DOOR COURTESY SW)
3.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.

Inspect the electric parking brake switch (electric parking brake switch assembly).

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-31 (SWI1) - F67-6 (SWI1) Always Below 5 Ω
A42-32 (SWO1) - F67-5 (SWO1) Always Below 5 Ω
A42-15 (SWI2) - F67-4 (SWI2) Always Below 5 Ω
A42-16 (SWO2) - F67-3 (SWO2) Always Below 5 Ω
A42-31 (SWI1) or F67-6 (SWI1) - Body ground Always 10 kΩ or higher
A42-32 (SWO1) or F67-5 (SWO1) - Body ground Always 10 kΩ or higher
A42-15 (SWI2) or F67-4 (SWI2) - Body ground Always 10 kΩ or higher
A42-16 (SWO2) or F67-3 (SWO2) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for CVT) A
OK (for Manual Transaxle) B
NG C



A

5.READ VALUE USING GTS (SHIFT POSITION)

B

7.READ VALUE USING GTS (NEUTRAL SWITCH)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (SHIFT POSITION)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift Position Shift lever position information "P,N", R, D/M, 1st-6th/B or Fail Actual shift lever position for Continuously Variable Transaxle
OK:

On the GTS screen, ON or OFF is displayed accordingly.


Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Shift Lever Position
50003 105 32

Result:
Result Proceed to
OK A
NG (for K114) B
NG (for K313) C
NG (for K313F) D



A

6.READ VALUE USING GTS (STOP LIGHT SW)

B

C

D

6.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Data List.


f.

Read the Data List according to the display on the GTS.

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch OFF or ON ON: Brake pedal depressed
OFF: Brake pedal released
-
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
Stop Light SW
50003 105 37
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (DOOR COURTESY SW)

NG

7.READ VALUE USING GTS (NEUTRAL SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Stop and Start / Data List.


f.

Read the Data List according to the display on the GTS.

Powertrain > Stop and Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Switch Neutral start switch assembly signal ON / OFF ON: Shift lever in neutral
OFF: Shift lever not in neutral
-
Powertrain > Stop and Start > Data List
Tester Display
Neutral Switch
50003 227 9
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE AND NO. 2 VOLTAGE)

NG

8.READ VALUE USING GTS (ACCELERATOR POSITION SENSOR NO. 1 VOLTAGE AND NO. 2 VOLTAGE)
A208621C06
0.667,1.75 1.448,2.177 0.781,0.427 10 *a 2.615,1.75 3.177,2.177 0.563,0.427 10 *b
*a Fully Depressed
*b Fully Released


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage.

Powertrain > Engine > Data List
Tester Display
Accelerator Position Sensor No.1 Voltage
Accelerator Position Sensor No.2 Voltage
50003 372 87,88

e.

Read the values displayed on the GTS.

Standard Voltage:
Accelerator Pedal Operation Accelerator Position Sensor No.1 Voltage Accelerator Position Sensor No.2 Voltage
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (CLUTCH STROKE SENSOR VOLTAGE)

NG

9.READ VALUE USING GTS (CLUTCH STROKE SENSOR VOLTAGE)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Data List.


f.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Clutch Stroke Sensor Voltage Clutch stroke sensor output voltage Min.: 0.000 V
Max.: 4.999 V
Value increases: Clutch pedal released → clutch pedal fully depressed -
Powertrain > Engine > Data List
Tester Display
Clutch Stroke Sensor Voltage
50003 372 607
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (DOOR COURTESY SW)

NG

10.READ VALUE USING GTS (DOOR COURTESY SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical > Main Body > Data List


f.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH (for RHD) ON or OFF ON: Front door RH open
OFF: Front door RH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
FL Door Courtesy SW Front door courtesy light switch assembly LH (for LHD) ON or OFF ON: Front door LH open
OFF: Front door LH closed
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part.
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
FL Door Courtesy SW
50003 123 197,199
OK:

The Data List item changes in accordance with the opening and closing of the driver door.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (D SEAT BUCKLE SW)

NG

11.READ VALUE USING GTS (D SEAT BUCKLE SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical > Main Body > Data List


f.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch OFF or ON ON: Driver seat belt unfastened
OFF: Driver seat belt fastened
-
Body Electrical > Main Body > Data List
Tester Display
D Seat Buckle SW
50003 123 14
OK:

Unset or Set is displayed on the GTS according to the driver seat belt condition.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

C