The skid control ECU judges brake failure conditions have occurred based on signals from the brake pedal load sensing switch and master cylinder pressure sensor.
Do not intentionally stop the engine when driving. Even when no malfunction has occurred in the brake system, DTC C1441 will be stored when it is judged that a failure has occurred in the brake system due to a reduction in vacuum.
DTCs may be stored if one of the following occurs:
The brake pedal load sensing switch is malfunctioning (deviation in characteristics).
The brake pedal is depressed when moving the vehicle with the engine not running and the ignition switch ON.
Bleeding is performed with the engine running or the ignition switch ON.
The accelerator and brake pedals depressed simultaneously.*
*: The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1441 | Performance Decline of Brake Function | When the brake pedal load sensing switch and master cylinder pressure sensor are functioning normally and the brake pedal load sensing switch is judged as on, the pressure signal from the master cylinder pressure sensor does not indicate an increase. | ·
Brake pedal load sensing switch (brake pedal support assembly) ·
Brake booster assembly ·
Skid control ECU (brake actuator assembly) |
Interview the customer to check if the pedals were depressed simultaneously while driving or braking.
The pedals were not depressed simultaneously.
The skid control ECU may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check and record DTCs and Freeze Frame Data (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR) for Check DTCs and Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>FREEZE FRAME DATAfor Freeze Frame Data).
Read Freeze Frame Data at the time DTC C1441 was stored, go to operation history and confirm the operating conditions.
When reading Freeze Frame Data to confirm operating conditions, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs and Freeze Frame Data (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR) for Clear DTCs and Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>FREEZE FRAME DATA) for Freeze Frame Data).
| Proceed to |
|---|
| NEXT |
NEXT
Based on the customer problem analysis, confirm the brake pedal condition at the time the brake pedal was operated.
| Result | Proceed to |
|---|---|
| The brake pedal is hard to depress. | A |
| The brake pedal is extremely easy to depress. | B |
| Neither of the above conditions. (Problem symptom does not occur.) | C |
A
B
C
Check the brake booster assembly (Click here Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>ON-VEHICLE INSPECTION) for LHD or (Click here Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>ON-VEHICLE INSPECTION) for RHD).
| Result | Proceed to |
|---|---|
| The brake booster assembly is abnormal. | A |
| The brake booster assembly is normal. | B |
If the result shows that the brake booster assembly is defective, check the related components such as the brake booster, brake vacuum check valve, vacuum warning switch assembly, check valve grommet, brake booster gasket, vacuum hose and intake system for vacuum leaks or clogs.
A
B
Check that the brake fluid level is sufficient.
If the fluid level is low, check for a fluid leaks, and repair as necessary.
Check for brake fluid leakage (brake master cylinder, brake line, flexible hose, brake actuator, wheel cylinders, etc.).
| Result | Proceed to |
|---|---|
| Brake fluid level is not sufficient. | A |
| Brake fluid level is sufficient. | B |
If brake fluid leaks are not found in components such as the brake master cylinder, brake line, flexible hose, brake actuator or wheel cylinders but the fluid level has become lower, the brake master cylinder may be leaking internally. Therefore, replace the brake master cylinder and check brake pedal operation again.
A
B
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR)).
Start the engine.
Perform a road test.
Do not intentionally stop the engine when driving. DTC C1441 will be stored if the brake pedal is depressed when moving the vehicle with the engine not running and the ignition switch ON.
Check if the same DTC is recorded.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1441 is not output. | A |
| DTCs C1441 and other DTC are output. | B |
| Only DTC C1441 is output. | C |
If DTC C1441 and other DTCs are output simultaneously, the other DTCs may have caused the engine to malfunction, resulting in DTC C1441 to be output. Read Freeze Frame Data to confirm malfunctioning parts and repair the applicable part.
When reading Freeze Frame Data to confirm malfunctioning parts, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".
A
B
C
Check that the matchmarks on the adjustment part of the brake pedal load sensing switch are aligned with the matchmarks on the brackets, nuts, adjusting screw, etc.
| *A | for LHD | *B | for RHD |
| *1 | Brake Pedal Load Sensing Switch | - | - |
| *a | Matchmark | - | - |
The matchmarks on the adjustment part of the brake pedal load sensing switch are aligned with the matchmarks on the brackets, nuts, adjusting screw, etc.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D