Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.10–2020.08
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0297889 DYNAMIC RADAR CRUISE CONTROL SYSTEM Y

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Perform the following procedure to troubleshoot the dynamic radar cruise control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Turn the cruise control main switch (ON/OFF) on.


g.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Misalignment Reading
50005 220 4405

i.

Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.


j.

Check the amount of offset and make a note.

Body Electrical > Pre-Collision 2 > Utility
Tester Display
Front Beam Axis Offset Reading
50005 220 4406

k.

Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".

i.

"Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"

Standard:
Dealership Axis Offset Angle (with On-line Calibration Angle):
Vertical -5.2 to 5.2 deg.
Horizontal -0.6 to 0.6 deg.




Result:
Result Proceed to
The dealership axis offset angle (with on-line calibration angle) is within the specified range. A
The dealership axis offset angle (with on-line calibration angle) is not within the specified range. B



A

4.CHECK CAN COMMUNICATION SYSTEM*

B

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

5.CHECK METER / GAUGE SYSTEM*

B

5.CHECK METER / GAUGE SYSTEM*
a.

Use the GTS to check if the meter / gauge system is functioning normally.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
Meter / gauge system DTCs are not output A
Meter / gauge system DTCs are output B



A

6.CHECK VEHICLE STABILITY CONTROL SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM

B

6.CHECK VEHICLE STABILITY CONTROL SYSTEM AND ELECTRIC PARKING BRAKE SYSTEM
a.

Use the GTS to check if the vehicle stability control system and electric parking brake system are functioning normally.

Vehicle stability control system: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Electric parking brake system: Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
Vehicle stability control system and electric parking brake system DTCs are not output A
Vehicle stability control system DTCs are output B
Electric parking brake system DTCs are output C



A

7.CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM)

B

C

7.CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM)
a.

Check for DTCs and note any codes that are output.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

b.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 374
Powertrain > Radar Cruise2 > Clear DTCs
50002 197

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 374
Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

8.PROBLEM SYMPTOMS TABLE

B

8.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

9.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

10.ADJUST, REPAIR OR REPLACE
NOTICE:

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

11.CONFIRMATION TEST
11.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END

12.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*