Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM › 2016.10–2019.09
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0298220 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1299/99  Cancellation of 4WD Control  


DESCRIPTION

This DTC is output if the heat generated by the transmission coupling assembly exceeds a certain amount or if the estimated oil temperature of the transfer exceeds a certain amount while driving.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1299/99 Cancellation of 4WD Control When one of the following conditions is met:
·

Condition that controls coupling calorific value is predefined value or more.

·

Condition that transfer oil temperature is predefined value or more.


·

Condition, size or tire pressure of the front or rear tires

·

Suspension and ball joint

·

Drive shaft

·

Propeller shaft

·

Transmission coupling assembly

·

4WD ECU assembly



CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK VEHICLE USAGE
a.

Check that there has been no unintended vehicle usage.

OK:

There is no evidence of rough use (the vehicle has not been driven on damaged or snowy roads, etc. for a long time).



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTC

NG

2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check if the brake control system DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only "C1299/99" is output A
"C1299/99" and other DTCs (brake control system DTC) B




A

3.CHECK RELATED PART

B

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

3.CHECK RELATED PART
a.

Check the condition, size and tire pressure of the front and rear tires.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION


b.

Inspect the suspension and ball joint, etc. for rattle.


c.

Inspect the drive shaft and propeller shaft rotation condition.


Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Result Proceed to
DTC is output A
DTC is not output B




A

5.REPLACE 4WD ECU ASSEMBLY

B

5.REPLACE 4WD ECU ASSEMBLY
a.

Replace the 4WD ECU assembly.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>4WD CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC
6.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle at a speed of 20 km/h (12 mph) or more and check that the same DTC is output.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118

Result:
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE TRANSMISSION COUPLING ASSEMBLY

B

END