This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2274 | ACC Monitor Malfunction | The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*)
|
·
AM2 fuse ·
Instrument panel junction block assembly ·
Certification ECU (Smart key ECU assembly) ·
Wire harness or connector |
DTC Output Confirmation Operation:
Wait 10 seconds after turning the engine switch on (ACC) or on (IG), and then wait another 10 seconds after turning the engine switch off. |
*: Only detected while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
·
If there is a malfunction due to the ACC relay being stuck on, the ACC relay does not turn off even though the engine switch is off. ·
If there is a malfunction due to the ACC relay being stuck off, the ACC relay does not turn on even though the engine switch is on (ACC).
|
- |
| DTC No. | Data List and Active Test |
|---|---|
| B2274 | Power Source Control
·
ACC Relay Monitor Starting Control
·
Ignition |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Inspect the fuses of circuits related to this system before performing the following procedure.
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Start Function) Precaution.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>B2271
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F1 certification ECU (smart key ECU assembly) connector.
Disconnect the 3A and 3D instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F1-16 (ACCD) - 3A-30 | Always | Below 1 Ω |
| 3D-3 - Body ground | Always | Below 1 Ω |
| F1-16 (ACCD) or 3A-30 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3A-30 - 3D-3 | 20°C (68°F) | 285.71 to 428.57 Ω |
| 3K-1 - 3A-40 | Battery voltage not applied between terminals 3A-30 and 3D-3 | 10 kΩ or higher |
| Battery voltage not applied between terminals 3A-30 and 3D-3 | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
Reconnect the F1 certification ECU (smart key ECU assembly) connector.
Install the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F1-16 (ACCD) - Body ground | Engine switch off → Engine switch on (ACC) | 1 V or less → 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG