Home › Power Source / Network › POWER DISTRIBUTION › MAIN BODY ECU (for LHD) › 2016.10–2020.08
RM32H0E _57 Power Source / Network _060596 POWER DISTRIBUTION _0297231 MAIN BODY ECU(for LHD) A

POWER DISTRIBUTION  MAIN BODY ECU(for LHD)  INSTALLATION  


PROCEDURE

Hide 89221 1.INSTALL MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NOTICE:
·

Make sure that the connecting surfaces are free of foreign matter.

·

Do not touch the main body ECU (multiplex network body ECU) connector.



a.
E336539C01
0.417,0.948 0.927,1.448 true 0.344,2.292 0.656,2.448 0.313,0.156 10 false *a 0.219,0.844 0.531,1 0.313,0.156 10 false *b
*a 20° or more
*b Housing Sidewall
V113147

Set in this Direction


Set the main body ECU (multiplex network body ECU) to the position where the guide of the main body ECU (multiplex network body ECU) contacts the housing sidewall of the instrument panel junction block assembly as shown in the illustration.

HINT:

Make sure to keep the angle at 20° or more as shown in the illustration.



b.
E336542C01
0.385,0.854 0.969,1.417 true 0.177,0.729 0.49,0.885 0.313,0.156 10 false *a
*a Housing Sidewall
V113147

Slide in this Direction


Slide the main body ECU (multiplex network body ECU) along the housing sidewall as shown in the illustration and engage the guides.


c.
E336544C01
2.219,0.844 2.833,0.448 true 2.896,0.365 3.208,0.521 0.313,0.156 10 false *a
*a Side A
V113147

Install in this Direction


While keeping the main body ECU (multiplex network body ECU) in contact with side A of the instrument panel junction block assembly (axis of rotation), lower it as shown in the illustration.


d.
E336546C01
0.719,2.823 1.208,2.823 true 0.188,2.802 0.51,2.802 true 1.24,2.729 1.552,2.885 0.313,0.156 10 false *1 0.021,2.708 0.333,2.865 0.313,0.156 10 false *2
*1 Instrument Panel Junction Block Assembly
*2 Main Body ECU (Multiplex Network Body ECU)
V100155

Push Area


Press the push area until the claw engages to install the main body ECU (multiplex network body ECU).

NOTICE:
·

Make sure to press only the push area.

·

Confirm the engagement of the main body ECU (multiplex network body ECU) and instrument panel junction block assembly by listening for the click sound of the lock engaging.



HINT:

If a click sound cannot be heard, visually check the engagement of the lock. The engagement can also be confirmed if the main body ECU (multiplex network body ECU) and instrument panel junction block assembly are flush.



e.
E353749

Engage the clamp to install the wiring harness clamp bracket.


f.

Temporarily install the bolt.

HINT:

Do not fully tighten the bolt.



Hide 82730 2.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU

a.
E353754C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the lock levers to engage the claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



b.

Engage the clamp.


c.
E353747

Engage the clamp.


d.
E353746

Engage the clamp to install the instrument panel junction block assembly with main body ECU.


e.

Install the bolt and nut.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


f.
E359069

Tighten the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.
E353755C01
0,0 0,0 false
V113147

Install in this Direction


Connect the 2 connectors and raise the 2 lock levers to engage the claws and lock the connector as shown in the illustration.

NOTICE:

Be sure to connect the connector securely.



h.

Disconnect 4 connectors.


i.
E353743

Engage the clamp.


Hide 55308B 3.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

Hide 55545 4.INSTALL FUSE BOX OPENING COVER (w/o Driver Side Knee Airbag)

Hide 53601 5.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55404D 6.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55434B 7.INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Driver Side Knee Airbag)

Hide 55470 8.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 55606 9.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

Hide 62112 10.INSTALL COWL SIDE TRIM BOARD LH (w/o Driver Side Knee Airbag)

Hide 67914 11.INSTALL FRONT DOOR SCUFF PLATE LH (w/o Driver Side Knee Airbag)

Hide 73900 12.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION