Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM
RM32H0E _58 Vehicle Interior _060065 SEAT BELT _0299547 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Rear Seat Belt Warning Light Malfunction  


DESCRIPTION

The combination meter assembly detects whether either rear door is open or closed based on the condition of the left and right courtesy light switches. The combination meter assembly detects the rear seat belt state. The rear seat belt warning lights on the clock assembly illuminate or turn off in accordance with the rear door state, vehicle speed and rear seat belt state.

WIRING DIAGRAM

A394821E01
0.958,0.167 1.417,0.365 0.458,0.198 10 false IG+ 1.323,0.156 1.781,0.354 0.458,0.198 10 false 1 0.906,0.896 1.365,1.094 0.458,0.198 10 false RLID 1.292,0.896 1.75,1.094 0.458,0.198 10 false 12 1.292,1.469 1.75,1.667 0.458,0.198 10 false 13 1.292,2.063 1.75,2.26 0.458,0.198 10 false 14 1.333,2.365 1.792,2.563 0.458,0.198 10 false 5 0.896,1.49 1.354,1.688 0.458,0.198 10 false RCID 0.865,2.094 1.323,2.292 0.458,0.198 10 false RRID 0.125,2.802 0.583,3 0.458,0.198 10 false F81 0.115,2.969 1.49,3.167 1.375,0.198 10 false Clock Assembly 1.917,0.906 2.375,1.104 0.458,0.198 10 false RLMT 1.917,1.5 2.375,1.698 0.458,0.198 10 false RCMT 1.927,2.083 2.385,2.281 0.458,0.198 10 false RRMT 3.396,0.781 3.854,0.979 0.458,0.198 10 false CPU 3.875,0.396 5.083,0.594 1.208,0.198 10 false ECU-IG1 NO. 4 5.448,0.25 6.865,0.583 1.417,0.333 10 false from IG1-NO. 1 Relay 3.469,1.667 3.927,1.865 0.458,0.198 10 false I/F 1.51,4.99 2.094,5.156 0.583,0.167 10 false LCTY 2.063,3.219 3.104,3.5 1.042,0.281 10 false Output Driver 1.479,6.052 2.063,6.219 0.583,0.167 10 false RCTY 2,4.875 2.333,5.042 0.333,0.167 10 false 13 2,5.958 2.333,6.125 0.333,0.167 10 false 2 3.531,4.802 3.865,4.969 0.333,0.167 10 false 24 3.521,5 3.854,5.167 0.333,0.167 10 false 3H 3.521,5.875 3.854,6.042 0.333,0.167 10 false 31 3.5,6.063 3.833,6.229 0.333,0.167 10 false 3A 0.792,7.333 2.792,7.5 2,0.167 10 false : CAN Communication Line 0.177,6.417 0.594,6.583 0.417,0.167 10 false MB 0.177,6.583 1.844,7 1.667,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 1.948,6.396 3.615,6.813 1.667,0.417 10 false Instrument Panel Junction Block Assembly 3.771,6.583 7.021,6.833 3.25,0.25 10 false Rear Door Courtesy Light Switch Assembly (for RH) 3.76,6.417 4.094,6.583 0.333,0.167 10 false M58 3.781,5.354 4.115,5.521 0.333,0.167 10 false M16 3.771,5.521 7.021,5.771 3.25,0.25 10 false Rear Door Courtesy Light Switch Assembly (for LH) 4.427,4.896 4.76,5.063 0.333,0.167 10 false 1 4.458,5.938 4.792,6.104 0.333,0.167 10 false 1 4.719,3.625 6.479,4.042 1.76,0.417 10 false Rear Seat Inner with Center Belt Assembly LH 5.365,3.313 5.948,3.479 0.583,0.167 10 false for LH 5.333,2.802 6.167,2.969 0.833,0.167 10 false for Center 4.51,3.188 4.885,3.354 0.375,0.167 10 false M32 4.51,2.667 4.885,2.833 0.375,0.167 10 false M33 6.448,2.667 6.823,2.833 0.375,0.167 10 false M33 6.448,3.198 6.823,3.365 0.375,0.167 10 false M32 4.854,2.573 5.354,2.74 0.5,0.167 10 false CBR+ 4.865,3.104 5.365,3.271 0.5,0.167 10 false LBR+ 6.031,2.563 6.531,2.729 0.5,0.167 10 false CBR- 6.073,3.083 6.573,3.25 0.5,0.167 10 false LBR- 4.583,1.635 5.083,1.802 0.5,0.167 10 false M31 4.583,1.802 6.917,2.052 2.333,0.25 10 false Rear Seat Inner Belt Assembly RH 4.677,1.208 4.885,1.406 0.208,0.198 10 false 5 4.865,1.219 5.365,1.385 0.5,0.167 10 false RBR+ 6,1.219 6.5,1.385 0.5,0.167 10 false RBR- 6.448,1.219 6.656,1.417 0.208,0.198 10 false 4 2.25,3.99 2.667,4.156 0.417,0.167 10 false F4 2.24,4.135 4.323,4.385 2.083,0.25 10 false Combination Meter Assembly 4.604,3 4.813,3.198 0.208,0.198 10 false 4 4.594,2.479 4.802,2.677 0.208,0.198 10 false 1 6.521,3.01 6.729,3.208 0.208,0.198 10 false 5 6.531,2.49 6.74,2.688 0.208,0.198 10 false 2 1.74,0.896 2.198,1.094 0.458,0.198 10 false 1 1.74,1.5 2.198,1.698 0.458,0.198 10 false 2 1.729,2.083 2.188,2.281 0.458,0.198 10 false 3 1.083,2.448 1.542,2.646 0.458,0.198 10 false E 3.844,2.594 4.271,2.74 0.427,0.146 10 false MSTI 4.26,2.563 4.469,2.76 0.208,0.198 10 false 25 3.854,3.094 4.281,3.24 0.427,0.146 10 false MSD 4.25,3.094 4.458,3.292 0.208,0.198 10 false 24 3.74,1.208 4.229,1.396 0.49,0.188 10 false MSFM 4.271,1.208 4.479,1.406 0.208,0.198 10 false 26

CAUTION / NOTICE / HINT

NOTICE:
·

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (REAR DOOR COURTESY LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Door Courtesy SW Rear door courtesy light switch RH ON or OFF ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW Rear door courtesy light switch LH ON or OFF ON: Rear door LH open
OFF: Rear door LH closed
-
Body Electrical > Main Body > Data List
Tester Display
RR Door Courtesy SW
RL Door Courtesy SW
50003 123 24,25

OK:

ON or OFF appears on the GTS screen according to the rear door condition.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS

NG

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
2nd-Row Seatbelt Buckle (R) Rear RH seat belt buckle switch signal ON or OFF ON: Rear RH seat belt not fastened
OFF: Rear RH seat belt fastened
-
2nd-Row Seatbelt Buckle (L) Rear LH seat belt buckle switch signal ON or OFF ON: Rear LH seat belt not fastened
OFF: Rear LH seat belt fastened
-
2nd-Row Seatbelt Buckle (C) Rear center seat belt buckle switch signal ON or OFF ON: Rear center seat belt not fastened
OFF: Rear center seat belt fastened
-
Body Electrical > Combination Meter > Data List
Tester Display
2nd-Row Seatbelt Buckle (R)
2nd-Row Seatbelt Buckle (L)
2nd-Row Seatbelt Buckle (C)
50003 122 74,75,76
OK:

The GTS display changes correctly in response to the rear door condition.



Result:
Result Proceed to
ON or OFF is displayed on the GTS screen according to the rear seat belt condition A
ON or OFF is not displayed normally on the GTS screen according to the rear LH seat belt condition B
ON or OFF is not displayed normally on the GTS screen according to the rear center seat belt condition B
ON or OFF is not displayed normally on the GTS screen according to the rear RH seat belt condition C



A

3.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - BATTERY)

B

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

C

8.INSPECT REAR SEAT INNER BELT ASSEMBLY RH
3.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - BATTERY)
a.
A394822C01
0.417,1 0.833,1.25 0.417,0.25 0.833,1.583 1.25,1.135 true 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 0.563,1.583 0.875,1.74 0.313,0.156 10 false IG+ 0.5,1.031 0.844,1.25 0.344,0.219 10 false F81
*a Front view of wire harness connector
(to Clock Assembly)


Disconnect the clock assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-1 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

4.INSPECT CLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT CLOCK ASSEMBLY
a.

Remove the clock assembly.

Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING LIGHT>REMOVAL


b.

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (CLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F81 clock assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-12 (RLID) - F4-1 (RLMT) Always Below 1 Ω
F81-13 (RCID) - F4-2 (RCMT) Always Below 1 Ω
F81-14 (RRID) - F4-3 (RRMT) Always Below 1 Ω
F81-12 (RLID) or F4-1 (RLMT) - Body ground Always 10 kΩ or higher
F81-13 (RCID) or F4-2 (RCMT) - Body ground Always 10 kΩ or higher
F81-14 (RRID) or F4-3 (RRMT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH
a.

Remove the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for LH Side)>REMOVAL


b.

Inspect the rear seat inner with center belt assembly LH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for LH Side)>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the M32 and M33 rear seat inner with center belt assembly LH connectors.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M32-4 (LBR+) - F4-24 (MSD) Always Below 1 Ω
M33-1 (CBR+) - F4-25 (MSTI) Always Below 1 Ω
M32-5 (LBR-) - Body ground Always Below 1 Ω
M33-2 (CBR-) - Body ground Always Below 1 Ω
M32-4 (LBR+) or F4-24 (MSD) - Body ground Always 10 kΩ or higher
M33-1 (CBR+) or F4-25 (MSTI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR SEAT INNER BELT ASSEMBLY RH
a.

Remove the rear seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>REMOVAL


b.

Inspect the rear seat inner belt assembly RH.

Click hereVehicle Interior>SEAT BELT>REAR SEAT INNER BELT ASSEMBLY(for RH Side)>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE REAR SEAT INNER BELT ASSEMBLY RH

9.CHECK HARNESS AND CONNECTOR (REAR SEAT INNER BELT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the M31 rear seat inner belt assembly RH connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M31-5 (RBR+) - F4-26 (MSFM) Always Below 1 Ω
M31-4 (RBR-) - Body ground Always Below 1 Ω
M31-5 (RBR+) or F4-26 (MSFM) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR