When the ignition switch is ON, the combination meter assembly monitors the state of the front passenger side seat and the front seat inner belt assembly (front passenger seat) and also whether the front passenger seat is occupied. If the front passenger side seat belt is not fastened, the seat belt warning light of the combination meter assembly blinks. If the seat belt is fastened, the warning light goes off.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.Check that the operation of the seat belt warning light is normal first.
Click hereVehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>ON-VEHICLE INSPECTION
If the seat belt warning light does not operate for both the driver seat and front passenger seat, replace the combination meter assembly.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| P-Seatbelt Buckle SW | Front passenger seat belt buckle switch signal | ON or OFF | ON: Front passenger seat belt not fastened
OFF: Front passenger seat belt fastened |
Perform the inspection while sitting in the front passenger side seat. |
| Tester Display |
|---|
| P-Seatbelt Buckle SW |
| Result | Proceed to |
|---|---|
| ON or OFF is displayed on the GTS screen according to the front passenger side seat belt condition and front passenger seat condition (occupied or unoccupied) | A |
| ON or OFF is not displayed normally on the GTS screen according to the front passenger side seat belt condition | B |
A
B
Disconnect the F4 combination meter assembly connector.
Disconnect the M53*1 or M51*2 front seat inner belt assembly (front passenger seat) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F4-7 (PKBI) - M53-3 (+) | Always | Below 1 Ω |
| F4-7 (PKBI) or M53-3 (+) - Body ground | Always | 10 kΩ or higher |
| M53-2 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F4-7 (PKBI) - M51-3 (+) | Always | Below 1 Ω |
| F4-7 (PKBI) or M51-3 (+) - Body ground | Always | 10 kΩ or higher |
| M51-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front seat inner belt assembly (front passenger seat).
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL
Inspect the front seat inner belt assembly (front passenger seat).
Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the separate type front seat cushion pad (occupant detection sensor).
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL
Inspect the separate type front seat cushion pad (occupant detection sensor).
Click hereVehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG