Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD) › 2016.10–2019.09
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0299735 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  INSTALLATION  


PROCEDURE

Hide 44785 1.INSTALL BRAKE BOOSTER GASKET

a.

Install a new brake booster gasket to the brake booster assembly.


Hide 44610 2.INSTALL BRAKE BOOSTER ASSEMBLY

a.

While pushing the suction pipe sub-assembly toward the bottom of the vehicle, temporarily install the brake booster assembly to the vehicle.

NOTICE:
·

Do not apply excessive force to the suction pipe sub-assembly.

·

Do not apply excessive force to the brake lines or refrigerant lines.




b.

Return the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube to their original positions.

NOTICE:

Do not apply excessive force to the brake tubes.



c.

Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.

NOTICE:

Fully tighten the lock nut when adjusting the brake pedal height.



d.
C366893N01
0.865,1.563 1.021,1.76 0.156,0.198 10 true 1 2.396,0.594 2.552,0.792 0.156,0.198 10 true 2 0.844,0.615 1,0.813 0.156,0.198 10 true 3 2.406,1.563 2.563,1.76 0.156,0.198 10 true 4

Install the 4 nuts to secure the brake booster assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:

Tighten the 4 nuts in the order shown in the illustration.



e.

Remove the protective tape.


f.

w/ Stop and Start System:

Connect the vacuum sensor assembly connector to the vacuum sensor assembly.


g.

w/ Vacuum Warning Switch:

i.

Connect the vacuum warning switch connector to the vacuum warning switch assembly.



Hide 88707 3.SEPARATE SUCTION PIPE SUB-ASSEMBLY (for TMMT Made)

a.

Install the suction pipe sub-assembly to the engine mounting sub-assembly and vehicle body with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88707 4.INSTALL SUCTION PIPE SUB-ASSEMBLY (for TMC Made)

a.

Engage the 2 clamps to install the suction pipe sub-assembly to the piping clamp.


Hide 5.INSTALL BRAKE TUBE

a.

Engage the 3 clamps to install a new No. 1 brake tube clamp to the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube.


b.

Engage the 2 clamps to install 2 new No. 2 brake tube clamps to the vehicle body.


c.

Engage the 6 clamps to install the 2 No. 2 brake tube clmaps to the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube.


d.

for Manual Transaxle:

i.

Engage the 2 clamps to install the clutch tube to the 2 brake tube clamps.



e.
C368501C01
1.688,4.302 2,4.458 0.313,0.156 10 false *a 1.323,2.698 1.583,2.917 0.26,0.219 10 true (A) 2.354,3.219 2.583,3.448 0.229,0.229 10 true (B) 2.677,2.99 2.906,3.219 0.229,0.229 10 true (B)
*a Torque Wrench Fulcrum Length


Engage the 11 clamps to install the 2 new No. 1 brake tube clmaps to the front No. 1 brake tube, front No. 2 brake tube, front No. 3 brake tube and front No. 5 brake tube.


f.

Temporarily install front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube to the correct position on the brake actuator assembly.


g.

Using a 10 mm and 12 mm union nut wrench, tighten the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow the brake tubes to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




h.

Temporarily install front No. 3 brake tube to the front flexible hose.


i.
C366886C01
1.729,2.875 2.042,3.031 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, tighten the front No. 3 brake tube.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow the brake tubes to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 6.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.

Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.


Hide 44750 7.INSTALL VACUUM HOSE ASSEMBLY

a.

Install the vacuum hose assembly to the vehicle body with the 2 nuts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 55225 8.INSTALL DASH PANEL HEAT INSULATOR

a.
C366880N01
1.771,0.104 2.021,0.323 0.25,0.219 10 true (A) 3.01,0.25 3.26,0.469 0.25,0.219 10 true (A)

Temporarily install dash panel heat insulator to the vehicle body with the 2 nuts (A).


b.
C366902N01
1.885,1.802 2.156,2.021 0.271,0.219 10 true (B)

Install the nut (B).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Tighten the 2 nuts (A).

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51441 9.INSTALL NO. 1 ENGINE UNDER COVER

Hide 47264A 10.INSTALL PUSH ROD PIN

Hide 47101A 11.INSTALL BRAKE PEDAL RETURN SPRING

Hide 31410 12.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 47201 13.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 15.INSPECT AND ADJUST BRAKE PEDAL