The headlight ECU sub-assemblies control the high beam headlights.
The main body ECU (multiplex network body ECU) controls the high beam headlights.
for LED Headlight
for Halogen Headlight
If the headlight ECU sub-assembly LH has been replaced, it is necessary to synchronize the vehicle information and initialize the headlight ECU sub-assembly LH.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>INITIALIZATION
Inspect the fuse for circuits related to this system before performing the following procedure.
Check the operation of the low beam headlights. If the low beam headlights do not operate normally, refer to Problem Symptoms Table.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1
*1: w/ Entry and Start System
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for LED Headlight | A |
| for Halogen Headlight | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Headlight High Beam | High beam headlights | ON or OFF | - |
| Tester Display |
|---|
| Headlight High Beam |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LH Side) | B |
| NG (for RH Side) | C |
A
B
C
Replace the headlight unit assembly LH with a new or known good one.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Check that the high beam light LH operate normally.
High beam light LH operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the headlight unit assembly RH with a new or known good one.
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for LED Headlight)>REMOVAL
Check that the high beam light RH operate normally.
High beam light RH operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Check that the high beam headlights illuminate.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Head Light Hi | High beam headlights | ON or OFF | - |
| Tester Display |
|---|
| Head Light Hi |
The high beam headlights illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the H-LP SHADE relay from the No. 1 engine room relay block.
Inspect the H-LP SHADE relay.
Click hereVehicle Exterior>LIGHTING (EXT)>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 2- Body ground | Always | 11 to 14 V |
| Relay terminal 5- Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A11 headlight assembly LH connector.
Disconnect the A29 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 3 - A11-3 (SOL) | Always | Below 1 Ω |
| Relay terminal 3 - A29-3 (SOL) | Always | Below 1 Ω |
| A11-6 (E) - Body ground | Always | Below 1 Ω |
| A29-6 (E) - Body ground | Always | Below 1 Ω |
| Relay terminal 3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F15 main body ECU (Multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 1 - F15-1 (DIM) | Always | Below 1 Ω |
| Relay terminal 1- Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C