Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P071011  Transmission Fluid Temperature Sensor "A" Circuit Short To Ground  


DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

HINT:

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071011 Transmission Fluid Temperature Sensor "A" Circuit Short To Ground There is a short in the CVT fluid temperature sensor circuit for 0.5 seconds (1 trip detection logic).
·

Wire harness or connector

·

Continuously variable transaxle assembly (CVT fluid temperature sensor)

·

ECM


Comes on DTC stored SAE Code:
P0712

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and can detect a short to ground in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*, the ECM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.

*: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.

HINT:

The CVT fluid temperature can be checked in the Data List.


WIRING DIAGRAM

C318996E24
1.49,1.74 3.458,1.927 1.969,0.188 10 false CVT Fluid Temperature Sensor 1.802,2.594 3.635,2.792 1.833,0.198 10 false Transmission Wire 0.74,3.302 3.531,3.5 2.792,0.198 10 false Continuously Variable Transaxle Assembly 6.052,3.302 6.969,3.646 0.917,0.344 10 false ECM 3.583,1.125 4.042,1.323 0.458,0.198 10 false OIL 3.625,2.104 4.083,2.302 0.458,0.198 10 false E2 3.917,2.104 4.375,2.302 0.458,0.198 10 false 7 3.917,1.135 4.375,1.333 0.458,0.198 10 false 1 5.323,1.125 5.781,1.323 0.458,0.198 10 false 84 5.594,1.125 6.052,1.323 0.458,0.198 10 false THO1 5.604,2.104 6.063,2.302 0.458,0.198 10 false ETHO 5.333,2.104 5.792,2.302 0.458,0.198 10 false 83 6.281,0.979 6.74,1.177 0.458,0.198 10 false 5 V 0.75,3.167 1.188,3.375 0.438,0.208 10 false C40 6.052,3.156 6.625,3.427 0.573,0.271 10 false C62

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the ignition switch to ON and wait for 3 seconds or more.



PROCEDURE

1.READ VALUE USING GTS (A/T OIL TEMPERATURE NO.1)
a.

Warm up the engine.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Transmission / Data List.

Powertrain > Transmission > Data List
Tester Display
A/T Oil Temperature No.1
50003 373 180

f.

According to the display on the GTS, read the Data List.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
A/T Oil Temperature No.1 CVT fluid temperature sensor value Min.: -40°C (-40°F)
Max.: 150°C (302°F)
·

Approximately 100°C (212°F): After stall speed test

·

Equal to ambient temperature: After cold soak


If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)
a.
C264597C37
2.5,0.875 2.729,0.5 2.729,0.5 2.896,0.5 true 2.49,1.188 2.729,1.552 2.729,1.552 2.906,1.552 true 0.198,0.219 0.51,0.417 0.313,0.198 10 false *a 2.948,0.417 3.365,0.583 0.417,0.167 10 false OIL 2.979,1.469 3.292,1.667 0.313,0.198 10 false E2
*a Component without harness connected
(Transmission Wire)


Disconnect the C40 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (OIL) - 7 (E2) Always 79 Ω to 156 kΩ
1 (OIL) - Body ground and other terminals Always 10 kΩ or higher
7 (E2) - Body ground and other terminals Always 10 kΩ or higher


HINT:

If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.

CVT Fluid Temperature Specified Condition
10°C (50°F) 5.6 to 7.3 kΩ
25°C (77°F) 3.5 kΩ
110°C (230°F) 0.22 to 0.27 kΩ



c.

Connect the C40 transmission wire connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C326700C26
1.427,0.198 1.813,0.427 0.385,0.229 0.385,1.635 0.854,1.094 true 1.302,1.646 0.927,1.083 true 0.125,0.083 0.438,0.24 0.313,0.156 10 false *a 1.25,1.667 2.01,1.885 0.76,0.219 10 false 84 (THO1) 1.51,0.24 1.969,0.438 0.458,0.198 10 false C62 0.281,1.677 1.042,1.896 0.76,0.219 10 false 83 (ETHO)
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-84 (THO1) - C62-83 (ETHO) Always 79 Ω to 156 kΩ
C62-84 (THO1) - Body ground and other terminals Always 10 kΩ or higher
C62-83 (ETHO) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

5.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT