The ECM controls the secondary oil pressure based on the secondary oil pressure signal output by the oil pressure sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P084000 | Transmission Fluid Pressure Sensor/Switch "A" Circuit Range/Performance | Either one of the following conditions is met (1 trip detection logic):
·
When the requested oil pressure is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more, the oil pressure sensor output is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less for 2 seconds or more. ·
When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the difference between the calculated primary pulley pressure and target primary pulley pressure is 2.0 MPa (20.4 kgf/cm2, 290 psi) or more for 3 seconds or more. |
·
Oil pressure sensor ·
ECM |
Comes on (Euro-OBD)
Does not come on (Except Euro-OBD) |
DTC stored | SAE Code:
P0841 |
| P28287F | Pressure Control Solenoid "K" Actuator Stuck Off | One of the following conditions is met (1 trip detection logic):
·
When the requested oil pressure is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less, the oil pressure sensor output is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more for 3 seconds or more. ·
When the vehicle speed is less than 8 km/h (5 mph), the ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value for 0.2 seconds or more. ·
When the oil pressure sensor output is less than 0.35 MPa (3.6 kgf/cm2, 51 psi) and the target gear ratio is 2.0 or more, the actual gear ratio is less than 1.0 for 1.5 seconds or more. |
·
Continuously variable transaxle assembly ·
ECM |
Comes on (Euro-OBD)
Does not come on (Except Euro-OBD) |
DTC stored | SAE Code:
P2829 |
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnostic Condition | The requested oil pressure value is 1.4 MPa (14.3 kgf/cm2, 203 psi) or more. | ○ | - |
| The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. | - | ○ | |
| Malfunction Condition | The oil pressure sensor output value is 0.5 MPa (5.1 kgf/cm2, 73 psi) or less. | ○ | - |
| The difference between the calculated primary pulley pressure and target primary pulley pressure is 2.0 MPa (20.4 kgf/cm2, 290 psi) or more. | - | ○ | |
| Duration | 2 seconds or more | 3 seconds or more | |
| Detection Logic | 1 trip detection logic | 1 trip detection logic | |
This DTC is output when either of the above detection patterns is met.
| Vehicle Condition | ||||
|---|---|---|---|---|
| Pattern 1 | Pattern 2 | Pattern 3 | ||
| Diagnostic Condition | The requested oil pressure value is 1.0 MPa (10.2 kgf/cm2, 145 psi) or less. | ○ | - | - |
| The vehicle speed is less than 8 km/h (5 mph). | - | ○ | - | |
| The oil pressure sensor output value is less than 0.35 MPa (3.6 kgf/cm2, 51 psi) and the target gear ratio is 2.0 or more. | - | - | ○ | |
| Malfunction Condition | The oil pressure sensor output value is 2.5 MPa (25.5 kgf/cm2, 363 psi) or more. | ○ | - | - |
| The ratio of the transmission revolution sensor (NIN) output speed and transmission revolution sensor (NOUT) output speed exceeds a specified value. | - | ○ | - | |
| The actual gear ratio is less than 1.0. | - | - | ○ | |
| Duration | 3 seconds or more | 0.2 seconds or more | 1.5 seconds or more | |
| Detection Logic | 1 trip detection logic | 1 trip detection logic | 1 trip detection logic | |
This DTC is output when any one of the above detection patterns is met.
The ECM checks for belt clamping high-pressure or low-pressure malfunctions. If a mechanical malfunction of the shift solenoid valve SLS or the oil pressure sensor is detected by the ECM, it illuminates the MIL* and stores a DTC.
*: Euro-OBD
Do not perform a stall test if there are any people or objects near the vehicle.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform a stall test if any wheel chocks are out of position.
The vehicle could begin moving suddenly, resulting in a serious accident.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
The vehicle could begin moving suddenly, resulting in a serious accident.
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D position test in Road Test.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>ROAD TEST
Check for DTCs again.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
If any DTCs other than P084000 or P28287F are output, perform troubleshooting for those DTCs first.
| Result | Proceed to |
|---|---|
| Both DTC P084000 and P28287F are output | A |
| Only DTC P084000 is output | B |
| Only DTC P28287F is output | C |
| DTC P084000 and/or P28287F and other DTCs are output | D |
A
B
C
D
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test ·
3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test |
- |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure sensor.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Airbag sensor assembly (Yaw rate and acceleration sensor) |
After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P084000 and/or P28287F is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Airbag sensor assembly (Yaw rate and acceleration sensor) |
After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P28287F is output | A |
| DTCs are not output | B |
A
B
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test ·
3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test |
- |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure sensor.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>OIL PRESSURE SENSOR>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Performing Reset Memory will clear the learned values of the yaw rate and acceleration sensor (Deceleration Sensor Zero Point Calibration) and the CVT oil pressure (CVT Oil Pressure Calibration). Make sure to perform Reset Memory, Deceleration Sensor Zero Point Calibration, and CVT Oil Pressure Calibration if any of the parts in the following table have been replaced.
| Replaced Part |
|---|
·
Continuously variable transaxle assembly ·
ECM ·
Oil pressure sensor ·
Airbag sensor assembly (Yaw rate and acceleration sensor) |
After performing Reset Memory, always perform Deceleration Sensor Zero Point Calibration first, and then CVT Oil Pressure Calibration.
Always perform calibration with the vehicle on level ground (Inclination: 0 +/- 0.25°).
Do not shake or vibrate the vehicle during calibration.
Using the GTS, perform Reset Memory, Deceleration Sensor Zero Point Calibration and CVT Oil Pressure Calibration.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Perform a road test.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P084000 is output | A |
| DTCs are not output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Do not perform a stall test if there are any people or objects near the vehicle.
Do not perform a stall test if any wheel chocks are out of position.
Do not perform the stall test on a slippery or low-friction surface that could allow the tires to spin.
This test must be performed after checking and confirming that the engine is normal.
Perform this test with the CVT fluid temperature between 50 and 100°C (122 and 212°F).
Perform this test with the air conditioning off.
Do not perform the stall speed test for longer than 5 seconds
When performing the stall speed test repeatedly, wait for 15 seconds or more between tests.
Warm up the engine.
Fully apply the parking brake and chock all 4 wheels.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Activate the TC Terminal.
| Active Test Display |
|---|
| Activate the TC Terminal |
| Data List Display |
|---|
| Belt Clamping Force Sensor |
According to the display on the GTS, perform the Active Test.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Belt Clamping Force Sensor | Secondary oil pressure value | Min.: -64 MPa
Max.: 63.998 MPa |
Secondary oil pressure inspection:
·
3.5 to 5.5 MPa (35.6 to 56.1 kgf/cm2, 507 to 798 psi): D position stall test ·
3.6 to 5.5 MPa (36.7 to 56.1 kgf/cm2, 522 to 798 psi): R position stall test |
- |
| Result | Proceed to |
|---|---|
| Data List value is normal | A |
| Data List value is not normal | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the continuously variable transaxle assembly.
When Not Using the Engine Support Bridge
When Using the Engine Support Bridge
| Proceed to |
|---|
| NEXT |
NEXT