The clutch pedal stroke sensor assembly is mounted on the clutch pedal and detect the clutch pedal position and send signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P080512 | Clutch Position Sensor "A"Circuit Short to Battery | Clutch stroke sensor signal voltage is 4.8 V or more for 0.5 seconds or more (1 trip detection logic) | ·
Clutch pedal stroke sensor assembly ·
Open or short in clutch stroke sensor circuit ·
ECM |
Does not come on | DTC stored | SAE Code:
P0808 |
| P080514 | Clutch Position Sensor "A"Circuit Short to Ground or Open | Clutch stroke sensor signal voltage is 0.2 V or less for 0.5 seconds or more (1 trip detection logic) | ·
Clutch pedal stroke sensor assembly ·
Open or short in clutch stroke sensor circuit ·
ECM |
Does not come on | DTC stored | SAE Code:
P0807 |
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Drive the vehicle and confirm the lock-up on and off conditions according to Road Test.
Click hereDrivetrain>EC69 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>ROAD TEST
Turn the ignition switch off.
Perform step (1) again.
Check for DTCs again.
Click hereDrivetrain>EC69 (MANUAL TRANSMISSION / TRANSAXLE)>MANUAL TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmison / Data List / Clutch Stroke Sensor Voltage.
| Tester Display |
|---|
| Clutch Stroke Sensor Voltage |
Read the values displayed on the GTS.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| CLUTCH STROKE SENSOR VOLTAGE | Clutch pedal fully released | 0.5 to 1.1 V |
| Clutch pedal fully depressed | 2.6 to 4.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Clutch Pedal Stroke Sensor Assembly) |
Disconnect the clutch pedal stroke sensor assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A47-3 (VDD) - A47-1 (GND) | Ignition switch ON | 4.5 to 5.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C62 ECM connector.
Disconnect the A47 clutch pedal stroke sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-2 (OUT) - C62-119 (CLS) | Always | Below 1 Ω |
| C62-119 (CLS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the clutch pedal stroke sensor assembly.
for LHD
Click hereDrivetrain>CLUTCH>CLUTCH STROKE SENSOR (for LHD)>REMOVAL
for RHD
Click hereDrivetrain>CLUTCH>CLUTCH STROKE SENSOR (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmison / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P080512 or P080514 is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the C62 ECM connector.
Disconnect the A47 clutch pedal stroke sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A47-1 (GND) - C62-87 (E2CL) | Always | Below 1 Ω |
| A47-3 (VDD) - C62-89 (VCCL) | Always | Below 1 Ω |
| C62-87 (E2CL) - Body ground | Always | 10 kΩ or higher |
| C62-89 (VCCL) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT