Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0298708 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor)  B1442  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The No. 1 blower damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the air inlet damper to the appropriate position to change the air inlet mode (fresh, recirculation/fresh, and recirculation).

The air conditioning amplifier assembly communicates with the servo through a communication/driver IC and wiring assembly called the air conditioning harness assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1442 Air Inlet Damper Control Servo Motor Circuit Air inlet damper position sensor value does not change even if air conditioning amplifier assembly operates No. 1 blower damper servo sub-assembly
·

No. 1 blower damper servo sub-assembly

·

No. 1 air conditioning radiator damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly

·

Blower assembly


Memorized
(30 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E341943E19
0.792,8.542 3.083,8.802 2.292,0.26 10 false : LIN Communication Line 0.229,1.469 3.438,1.667 3.208,0.198 10 false Front Passenger Side Air Mix 0.656,3.448 3.865,3.646 3.208,0.198 10 false Mode Switching 0.625,5.406 3.833,5.604 3.208,0.198 10 false Driver Side Air Mix 0.573,6.063 2.5,6.51 1.927,0.448 10 false No. 1 Air Conditioning Radiator Damper Servo Sub-assembly 0.208,8.083 3.448,8.344 3.24,0.26 10 false No. 1 Blower Damper Servo Sub-assembly 3.167,8.094 6.406,8.354 3.24,0.26 10 false Air Conditioning Harness Assembly 5.49,8.125 7.094,8.594 1.604,0.469 10 false Air Conditioning Amplifier Assembly 5.49,7.958 5.865,8.146 0.375,0.188 10 false m1 5.344,0.292 5.771,0.479 0.427,0.188 10 false 4 5.344,1.135 5.771,1.323 0.427,0.188 10 false 3 5.354,2.063 5.781,2.25 0.427,0.188 10 false 2 5.542,0.292 7.031,0.51 1.49,0.219 10 false BUSB 5.542,1.177 7.031,1.396 1.49,0.219 10 false BUS 5.531,2.073 7.021,2.292 1.49,0.219 10 false BUS G 6.625,0.281 7.052,0.469 0.427,0.188 10 false +B 6.75,1.292 7.156,1.479 0.406,0.188 10 false IC 3.052,4.552 3.479,4.74 0.427,0.188 10 false 6 3.052,4.75 3.479,4.938 0.427,0.188 10 false 5 3.052,4.948 3.479,5.135 0.427,0.188 10 false 8 3.052,5.354 3.479,5.542 0.427,0.188 10 false 7 3.052,5.531 3.479,5.719 0.427,0.188 10 false 4 3.052,6.844 3.479,7.031 0.427,0.188 10 false 1 3.052,7.042 3.479,7.229 0.427,0.188 10 false 4 3.052,7.24 3.479,7.427 0.427,0.188 10 false 5 3.052,7.448 3.479,7.635 0.427,0.188 10 false 2 3.052,7.635 3.479,7.823 0.427,0.188 10 false 3 2.552,4.656 3.167,4.885 0.615,0.229 10 false STE2 2.573,4.854 3.188,5.083 0.615,0.229 10 false STE1 2.729,5.052 3.344,5.281 0.615,0.229 10 false M- 2.698,5.354 3.313,5.583 0.615,0.229 10 false M+ 2.604,5.531 3.219,5.76 0.615,0.229 10 false GND 2.594,6.844 3.208,7.073 0.615,0.229 10 false GND 2.698,7.042 3.313,7.271 0.615,0.229 10 false M+ 2.729,7.24 3.344,7.469 0.615,0.229 10 false M- 2.615,7.448 3.229,7.677 0.615,0.229 10 false sigA 2.625,7.635 3.24,7.865 0.615,0.229 10 false sigB

CAUTION / NOTICE / HINT

HINT:
·

Confirm that no mechanical problem is present because this DTC can be output when either a damper link or damper is mechanically locked.

·

When installing the damper servo motor, make sure to install it correctly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT (for DENSO Made)>REASSEMBLY



PROCEDURE

1.CHECK FOR DTC

Result:
Result Proceed to
DTC B1497 is output A
DTC B1441, B1442, B1443 and B1446 are output B
DTC B1442 is output C



A

B

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

C

2.INSPECT BLOWER ASSEMBLY
2.INSPECT BLOWER ASSEMBLY
a.

Remove the No. 1 blower damper servo sub-assembly.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT (for DENSO Made)>DISASSEMBLY


b.

Operate the air inlet control dampers by hand.

OK:

The air inlet control dampers are easily operated by hand.



Result:
Proceed to
OK
NG



OK

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY

NG

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY
a.

Disconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.


b.

Disconnect the No. 1 blower damper servo sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (STE2) - 3 (sigB) Always Below 1 Ω
5 (STE1) - 2 (sigA) Always Below 1 Ω
8 (M-) - 5 (M-) Always Below 1 Ω
7 (M+) - 4 (M+) Always Below 1 Ω
4 (GND) - 1 (GND) Always Below 1 Ω
6 (STE2) or 3 (sigB) - Body ground Always 10 kΩ or higher
5 (STE1) or 2 (sigA) - Body ground Always 10 kΩ or higher
8 (M-) or 5 (M-) - Body ground Always 10 kΩ or higher
7 (M+) or 4 (M+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (AIR INLET DAMPER TARG PULSE)

NG

4.PERFORM ACTIVE TEST USING GTS (AIR INLET DAMPER TARG PULSE)
a.

Reconnect the No. 1 air conditioning radiator damper servo sub-assembly connector.


b.

Reconnect the No. 1 blower damper servo sub-assembly connector.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / Air Conditioner / Active test.


g.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Air Inlet Damper Targ Pulse No. 1 blower damper servo sub-assembly pulse Min.: 128
Max.: 383
Operates between 220 to 256 pulses
Body Electrical > Air Conditioner > Active Test
Tester Display
Air Inlet Damper Targ Pulse
50004 121 27
OK:

No. 1 blower damper servo sub-assembly pulse operates smoothly.



Result:
Result Proceed to
No. 1 blower damper servo sub-assembly pulse are malfunctioning A
No. 1 blower damper servo sub-assembly pulse is normal B



A

5.CHECK HARNESS AND CONNECTOR (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY - BODY GROUND)

B

7.INSPECT NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
5.CHECK HARNESS AND CONNECTOR (NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the No. 1 blower damper servo sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

6.INSPECT NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
a.

Measure the voltage according to the value(s) in the table below.

Tester Connection Condition Specified Condition
4 (M+) - Body ground
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly operating (fresh)


11 to 14 V ←→ Below 1 V
5 (M-) - Body ground
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly operating (recirculation)


11 to 14 V ←→ Below 1 V


Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

7.INSPECT NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
a.
E361470C06
2.333,2.917 1.917,1.833 true 2.583,2.583 2.083,1.833 true 0.24,0.302 0.552,0.5 0.313,0.198 10 false *a 2.49,2.604 3.104,2.802 0.615,0.198 10 false sigA 2.229,2.938 2.844,3.135 0.615,0.198 10 false sigB
*a Component with harness connected
(No. 1 Blower Damper Servo Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
2 (sigA) - Body ground Ignition switch ON 4.75 V to 5.25 V
3 (sigB) - Body ground Ignition switch ON 4.75 V to 5.25 V



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

8.INSPECT NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY
a.

Turn the ignition switch ON.


b.
E361467C01
1.458,1.615 1.927,0.917 true 2.438,1.656 2.125,0.917 true 0.073,0.146 0.385,0.344 0.313,0.198 10 false *a 0.313,2.031 0.625,2.229 0.313,0.198 10 false *b 0.333,3.396 0.646,3.594 0.313,0.198 10 false *c 0.51,4.167 0.823,4.365 0.313,0.198 10 false GND 0.521,2.844 0.833,3.042 0.313,0.198 10 false GND 1.271,1.635 1.688,1.885 0.417,0.25 10 false sigB 2.344,1.667 2.76,1.917 0.417,0.25 10 false sigA
*a Component with harness connected
(No. 1 blower damper servo sub-assembly)
*b Fresh wave form
*c Recirculation wave form


Connect an oscilloscope to terminals 2 (sig A) and 3 (sig B) of the air conditioning amplifier assembly and check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Tool Setting 2.5 V/DIV., 200 ms./DIV.
Vehicle Condition
·

Ignition switch ON

·

No. 1 blower damper servo sub-assembly operating




Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE NO. 1 BLOWER DAMPER SERVO SUB-ASSEMBLY