The seat heater switch (air conditioning control assembly) communicates with the air conditioning amplifier assembly via LIN communication.
If the LIN communication system is malfunctioning, the air conditioning amplifier assembly will not operate even if the seat heater switch (air conditioning control assembly) is operated.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B14B5 | Lost Communication with Front Seat Temperature Adjustment Switch LIN | Lost communication with the seat heater switch (air conditioning control assembly) | ·
Seat heater switch (air conditioning control assembly) ·
Air conditioning amplifier assembly ·
Wire harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
When DTC B14B2 and B14B5 are output simultaneously, first perform troubleshooting for the air conditioning system.
for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor
for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor
Clear the DTCs.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR
DTC B14B5 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Front view of wire harness connector
(to Seat Heater Switch (Air Conditioning Control Assembly)) |
Disconnect the seat heater switch (air conditioning control assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F61-10 (IG+) - Body ground | Ignition switch ON | 11 to 14 V*1
10.5 to 16 V*2 |
| Ignition switch off | Below 1 V |
*1: w/o Stop and Start System
*2: w/ Stop and Start System
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F61-16 (GND) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Stop and Start System) | B |
| NG (w/ Stop and Start System) | C |
A
B
C
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the F61 seat heater switch (air conditioning control assembly) connector.
Disconnect the F72*1 or F73*2 air conditioning amplifier assembly connector.
*1: for Automatic Air Conditioning System with Top-mounted Air Conditioner Pressure Sensor
*2: for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F61-2 (LIN1) - F72-3 (LIN1) | Always | Below 1 Ω |
| F61-2 (LIN1) or F72-3 (LIN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F61-2 (LIN1) - F73-14 (LIN1) | Always | Below 1 Ω |
| F61-2 (LIN1) or F73-14 (LIN1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seat heater switch (air conditioning control assembly) with a new or known good one.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING PANEL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR
DTC B14B5 is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
Click hereVehicle Interior>SEAT>SEAT HEATER SYSTEM>DTC CHECK / CLEAR
DTC B14B5 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG