Refer to DTC P245211.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P245211
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P245215 | Particulate Filter Pressure Sensor "A" Circuit Short to Battery or Open | The output voltage from the differential pressure sensor (bank 1) is higher than 4.8 V for 3 seconds or more (1 trip detection logic). | ·
Open or short in differential pressure sensor circuit ·
Differential pressure sensor ·
ECM |
Does not come on | DTC stored | SAE Code:
P2455 |
When a DTC is output, check the Data List item "GPF Differential Pressure Sensor Bank 1" using the GTS.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
| DTC No. | GPF Differential Pressure Sensor Bank 1 | Malfunction |
|---|---|---|
| P245215 | 100 kPa [14.5 psi] or higher | ·
Short in VC circuit to PEX circuit ·
Open in PEX circuit ·
Open in EPEX circuit |
If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.
In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.
Example:
When the sensor output voltage is higher than 4.8 V for 3 seconds or more, the ECM stores a DTC.
| Frequency of Operation | Continuous |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and wait 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P245215.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Refer to DTC P245211.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P245211
Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.
| *a | Front view of wire harness connector
(to Differential Pressure Sensor) |
Disconnect the C73 differential pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-3 (VC) - C73-1 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| C73-2 (PEX) - C73-1 (E2) | Ignition switch ON | 3.0 to 5.5 V |
Turn the ignition switch off and wait for at least 30 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-3 (VC) - C73-2 (PEX) | Ignition switch ON | 171 to 189 kΩ |
| C73-1 (E2) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the C73 differential pressure sensor connector.
Disconnect the C62 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C73-2 (PEX) - C62-78 (PEX) | Always | Below 1 Ω |
| C73-1 (E2) - C62-79 (EPEX) | Always | Below 1 Ω |
| C73-2 (PEX) or C62-78 (PEX) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG