Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2018.05
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P24522A  Particulate Filter Pressure Sensor "A" Signal Stuck In Range  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P24522A Particulate Filter Pressure Sensor "A" Signal Stuck In Range During idling after warm-up, the differential pressure sensor output pulsation is below the specified value for 1 second or more (1 trip detection logic).
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

Vacuum transmitting hose assembly

·

Vacuum transmitting pipe

·

ECM


Does not come on DTC stored SAE Code:
P2453

MONITOR DESCRIPTION

When the differential pressure sensor output pulsation is below the specified value during idling after warm up, clogging or a hole in the differential pressure sensor pipe is judged and the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

7.

Idle the engine for 1 minute or more.

8.

Turn the GTS on.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P24522A.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P24522A)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P24522A is output A
DTC P24522A and other DTCs are output B


HINT:

If any DTCs other than P24522A are output, troubleshoot those DTCs first.




A

2.CHECK FOR EXHAUST GAS LEAK

B

2.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.


HINT:

Perform "Inspection After Repair" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK CONNECTION OF VACUUM TRANSMITTING HOSE ASSEMBLY (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

3.CHECK CONNECTION OF VACUUM TRANSMITTING HOSE ASSEMBLY (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)
a.

Check the vacuum transmitting hose assembly is no exhaust gas leak between the differential pressure sensor and the vacuum transmitting pipe.

OK:

The vacuum transmitting hose assembly is no exhaust gas leak.



Result:
Proceed to
OK
NG



OK

4.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND TRANSMITTING PIPE

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.CHECK BLOCKAGE OF VACUUM TRANSMITTING HOSE ASSEMBLY AND TRANSMITTING PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.

Disconnect vacuum transmitting hose assembly on the differential pressure sensor.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from vacuum transmitting hose assembly during idling.


Result:
Proceed to
OK
NG



OK

5.INSPECT DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

5.INSPECT DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

8.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P24522A)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P24522A)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the Pending DTCs.

OK:

DTCs are not output



Result:
Proceed to
NEXT



NEXT

END

8.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the C73 differential pressure sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C73-3 (VC) - C62-80 (VC) Always Below 1 Ω
C73-2 (PEX) - C62-78 (PEX) Always Below 1 Ω
C73-1 (E2) - C62-79 (EPEX) Always Below 1 Ω
C73-3 (VC) or C62-80 (VCPP) - Body ground and other terminals Always 10 kΩ or higher
C73-2 (PEX) or C62-78 (PEX) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE DIFFERENTIAL PRESSURE SENSOR

b.

Start the engine and allow it to idle until the engine coolant temperature reaches 75°C (167°F) or higher (A).


c.

Turn the ignition switch off and wait for 30 seconds or more (B).


d.

Repeat the above procedures (A) and (B) 3 times.

HINT:

Procedures (A) and (B) must be repeated 3 times to complete the differential pressure sensor learning process.



Result:
Proceed to
NEXT



NEXT

END