Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › from 2018.05
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299013 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B416786E12
2.021,0.333 2.521,0.583 0.5,0.25 3.208,0.333 3.708,0.583 0.5,0.25 4.5,0.333 5,0.583 0.5,0.25 2.146,0.365 2.458,0.563 0.313,0.198 10 false M66 3.333,0.365 3.646,0.563 0.313,0.198 10 false M67 4.677,0.365 4.99,0.563 0.313,0.198 10 false F1

a.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F1-18 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F1-4 (+B) - F1-18 (E) Input L - W-B Power supply Always 11 to 14 V -
F1-15 (CUTB) - F1-18 (E) Input SB - W-B Dark current cut pin* Always 11 to 14 V -

*: In order to prevent the vehicle battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is installed in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the vehicle battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of radio waves every 0.25 seconds, which form the detection area, stops).



c.

Reconnect the F1 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
F1-17 (IG1D) - F1-18 (E) Output GR - W-B IG power supply Engine switch off → on (IG) Below 1 V → 10 V or higher -
M67-17 (CLG1) - F1-18 (E) Output G - W-B Output to driver door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 1)
Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 2)
M67-17 (CLG1) - F1-18 (E) Input G - W-B Input to driver door lock sensor
(front door outside handle assembly (for driver door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)

5.

Driver door lock sensor touched


Pulse generation
(See waveform 3)
D-Door Trigger Switch
M67-17 (CLG1) - F1-18 (E) Input G - W-B Input to driver door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Driver door unlock sensor touched


Pulse generation
(See waveform 4)
D-Door Touch Sensor
M67-16 (CG1B) - F1-18 (E) Output R - W-B*1
BR - W-B*2
Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 5)
Overhead + Driver Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 6)
M67-15 (CLG2) - F1-18 (E) Output G - W-B*1
P - W-B*2
Output to front passenger door electrical key antenna
(request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 1)
Overhead + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 2)
M67-15 (CLG2) - F1-18 (E) Input G - W-B*1
P - W-B*2
Input to front passenger door lock sensor
(front door outside handle assembly (for front passenger door) lock sensor on signal is sent to the certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)

5.

Front passenger door lock sensor touched


Pulse generation
(See waveform 3)
P-Door Trigger Switch
M67-15 (CLG2) - F1-18 (E) Input G - W-B*1
P - W-B*2
Input to front passenger door unlock sensor
(when system is in unlock standby mode and unlock sensor is touched, door electrical key antenna sends unlock sensor input signal (sensing) to certification ECU (smart key ECU assembly))
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Front passenger door unlock sensor touched


Pulse generation
(See waveform 4)
P-Door Touch Sensor
M67-14 (CG2B) - F1-18 (E) Output R - W-B Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*3)


Pulse generation
(See waveform 5)
Overhead + Passenger Side (key diagnostic mode)
Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*3)


Pulse generation
(See waveform 6)
F1-8 (CLG5) - F1-18 (E) Output G - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 7)
Overhead + Front Room (key diagnostic mode)
F1-9 (CG5B) - F1-18 (E) Output R - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 7)
Overhead + Front Room (key diagnostic mode)
M67-11 (CLG7) - F1-18 (E) Output B - W-B Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 7)
Overhead + Back Door (inside) (key diagnostic mode)
M67-10 (CG7B) - F1-18 (E) Output W - W-B Output to No. 3 indoor electrical key antenna assembly (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door


Pulse generation
(See waveform 7)
Overhead + Back Door (inside) (key diagnostic mode)
M67-13 (CLG8) - F1-18 (E) Output Y - W-B Output to electrical key antenna (outside luggage compartment) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation
(See waveform 8)
Overhead + Back Door (key diagnostic mode)
M67-12 (CG8B) - F1-18 (E) Output W - W-B Output to electrical key antenna (outside luggage compartment) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


Pulse generation
(See waveform 8)
Overhead + Back Door (key diagnostic mode)
M67-26 (TSW5) - F1-18 (E) Input LG - W-B Back door opener switch assembly (open switch) signal input Back door opener switch assembly (open switch) off → on Pulse generation
(See waveform 9)
Tr/B-Door Unlock SW
M67-27 (TSW6) - F1-18 (E) Input GR - W-B Back door opener switch assembly (lock switch) signal input Back door opener switch assembly (lock switch) off → on Pulse generation
(See waveform 9)
Tr/B-Door Lock SW
M67-18 (RCO) - F1-18 (E) Output LG - W-B Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 10)
-
M67-19 (RDAM) - F1-18 (E) Input GR - W-B Door control receiver verifies data received from electrical key transmitter sub-assembly.
Door control receiver sends data from electrical key transmitter sub-assembly to certification ECU (smart key ECU assembly) (Door control receiver intermittently grounds 12 V signal from certification ECU (smart key ECU assembly)).
Proceed:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed


Pulse generation
(See waveform 11)
-
M67-20 (CSEL) - F1-18 (E) Output V - W-B Communication channel switching circuit Procedure:
1.

Engine switch off

2.

All doors closed


Below 1 V → pulse generation -

*1: for LHD

*2: for RHD

*3: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



e.
B340872N01
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection M67-17 (CLG1) - F1-18 (E)
M67-15 (CLG2) - F1-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



f.
B340873N01
0.177,1.021 0.635,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection M67-17 (CLG1) - F1-18 (E)
M67-15 (CLG2) - F1-18 (E)
Tool Setting 5 V/DIV., 100 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



g.
B340877C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 0.677,1.917 1.135,2.115 0.458,0.198 10 false *a 1.646,2 1.969,2.156 0.323,0.156 10 false *b 2.615,1.917 3.073,2.115 0.458,0.198 10 false *a
*a Lock sensor not touched
*b Lock sensor touched


Using an oscilloscope, check waveform 3.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Tester Connection M67-17 (CLG1) - F1-18 (E)
M67-15 (CLG2) - F1-18 (E)
Tool Setting 5 V/DIV., 40 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)

5.

Lock sensor not touched → touched



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



h.
B340879C02
0.177,1.052 0.635,1.25 0.458,0.198 10 false GND 0.344,1.906 0.802,2.104 0.458,0.198 10 false *a 2.115,1.906 2.573,2.104 0.458,0.198 10 false *a 1.229,1.969 1.667,2.167 0.438,0.198 10 false *b
*a Unlock sensor not touched
*b Unlock sensor touched


Using an oscilloscope, check waveform 4.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Tester Connection M67-17 (CLG1) - F1-18 (E)
M67-15 (CLG2) - F1-18 (E)
Tool Setting 5 V/DIV., 50 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors locked

4.

Electrical key transmitter sub-assembly not near the vehicle

5.

Unlock sensor not touched → touched




i.
B367472N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 5.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 5 (Reference)
Item Content
Tester Connection M67-16 (CG1B) - F1-18 (E)
M67-14 (CG2B) - F1-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought inside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



j.
B367473N01
0.188,1.021 0.646,1.219 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 6.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 6 (Reference)
Item Content
Tester Connection M67-16 (CG1B) - F1-18 (E)
M67-14 (CG2B) - F1-18 (E)
Tool Setting 5 V/DIV., 100 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors closed

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

All doors locked through wireless operation

(electrical key transmitter sub-assembly brought outside detection area*)



*: For details about the entry function detection area, refer to Operation Check.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK



k.
B340874C02
0.188,1.042 0.646,1.24 0.458,0.198 10 false GND 1.01,1.917 1.469,2.115 0.458,0.198 10 false *a 2.135,1.938 2.594,2.135 0.458,0.198 10 false *b
*a For 30 seconds after any door closed
*b After 30 seconds or more have elapsed since any door closed


Using an oscilloscope, check waveform 7.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 7 (Reference)
Item Content
Tester Connection F1-8 (CLG5) - F1-18 (E)
F1-9 (CG5B) - F1-18 (E)
M67-11 (CLG7) - F1-18 (E)
M67-10 (CG7B) - F1-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door




l.
B340876N01
0.177,1.042 0.635,1.24 0.458,0.198 10 false GND

Using an oscilloscope, check waveform 8.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 8 (Reference)
Item Content
Tester Connection M67-13 (CLG8) - F1-18 (E)
M67-12 (CG8B) - F1-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on




m.
B251023C09
1.333,0.49 1.99,0.125 1.99,0.125 2.208,0.125 false 1.99,0.135 1.74,0.51 false 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.25,0.031 2.427,0.208 0.177,0.177 10 false *a
*a Checking for switch on signal at short intervals


Using an oscilloscope, check waveform 9.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 9 (Reference)
Item Content
Tester Connection M67-26 (TSW5) - F1-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch assembly (open switch) off → on

Waveform 9 (Reference)
Item Content
Tester Connection M67-27 (TSW6) - F1-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch assembly (lock switch) off → on


n.
B251178C12
0.198,1 0.531,1.198 0.333,0.198 10 GND 1.01,1.885 1.198,2.042 0.188,0.156 10 *a 2.021,1.885 2.208,2.042 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 10.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 10 (Reference)
Item Content
Tester Connection M67-18 (RCO) - F1-18 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

3.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed




o.
B251177C12
0.208,1 0.542,1.198 0.333,0.198 10 GND 1.021,1.896 1.208,2.052 0.188,0.156 10 *a 2.188,1.906 2.375,2.063 0.188,0.156 10 *b
*a Before lock or unlock switch of electrical key transmitter sub-assembly pressed
*b After lock or unlock switch of electrical key transmitter sub-assembly pressed


Using an oscilloscope, check waveform 11.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 11 (Reference)
Item Content
Tester Connection M67-19 (RDAM) - F1-18 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Engine switch off

2.

All doors locked

3.

Electrical key transmitter sub-assembly not inside vehicle

4.

Electrical key transmitter sub-assembly brought outside detection area but kept inside wireless function operational area

5.

Lock or unlock switch of electrical key transmitter sub-assembly not pressed → pressed





CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


B434105C36
2.146,3.104 2.542,3.344 0.396,0.24 4.604,3.083 5,3.323 0.396,0.24 1.396,4.573 1.792,4.813 0.396,0.24 3.729,4.583 4.125,4.823 0.396,0.24 5.292,4.615 5.688,4.854 0.396,0.24 6.292,4.625 6.688,4.865 0.396,0.24 4.646,6.229 5.042,6.469 0.396,0.24 1.51,6.208 1.906,6.448 0.396,0.24 3.417,7.844 3.813,8.083 0.396,0.24 1.667,1.479 1.906,1.479 true 4.031,0.813 4.031,0.24 4.031,0.24 4.146,0.24 true 1.667,1.802 1.906,1.802 true 1.604,0.646 1.604,0.302 1.604,0.302 1.719,0.302 false 1.438,2.792 1.438,1.469 1.438,1.469 1.552,1.469 true 1.438,1.802 1.552,1.802 true 1.969,1.427 2.281,1.625 0.313,0.198 10 false F15 4.229,0.167 4.542,0.365 0.313,0.198 10 false MB 0.875,1.115 1.188,1.313 0.313,0.198 10 false 3H 0.885,1.656 1.198,1.854 0.313,0.198 10 false 3F 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3L 0.896,2.25 1.208,2.448 0.313,0.198 10 false 3K 1.969,1.729 2.281,1.927 0.313,0.198 10 false F16 5.854,1.135 6.167,1.333 0.313,0.198 10 false 3D 5.854,1.781 6.167,1.979 0.313,0.198 10 false 3A 4.698,3.125 5.01,3.323 0.313,0.198 10 false F15 2.219,3.146 2.531,3.344 0.313,0.198 10 false F16 1.521,4.615 1.833,4.813 0.313,0.198 10 false 3H 3.865,4.625 4.177,4.823 0.313,0.198 10 false 3F 5.417,4.667 5.729,4.865 0.313,0.198 10 false 3L 6.406,4.677 6.719,4.875 0.313,0.198 10 false 3K 1.625,6.26 1.938,6.458 0.313,0.198 10 false 3D 4.771,6.281 5.083,6.479 0.313,0.198 10 false 3A 3.531,7.896 3.844,8.094 0.313,0.198 10 false MB 0.115,0.146 0.604,0.385 0.49,0.24 12 false *A 1.771,0.25 2.677,0.448 0.906,0.198 10 false *1 1.365,2.833 2.271,3.031 0.906,0.198 10 false *a
*A Main Body ECU (Multiplex Network Body ECU) with 2 Connectors - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 2 Connectors - -


B434104C41
3.531,3.198 3.896,3.417 0.365,0.219 1.396,4.583 1.76,4.802 0.365,0.219 3.729,4.583 4.094,4.802 0.365,0.219 5.313,4.583 5.677,4.802 0.365,0.219 6.302,4.552 6.667,4.771 0.365,0.219 1.583,6.24 1.948,6.458 0.365,0.219 4.813,6.26 5.177,6.479 0.365,0.219 3.354,7.854 3.719,8.073 0.365,0.219 1.667,1.333 1.906,1.333 true 4,0.813 4,0.365 4,0.365 4.125,0.365 true 1.625,0.656 1.625,0.281 1.625,0.281 1.75,0.281 true 1.417,2.708 1.417,1.333 1.417,1.333 1.542,1.333 true 0.865,1.094 1.177,1.292 0.313,0.198 10 false 3H 0.865,1.646 1.177,1.844 0.313,0.198 10 false 3F 0.875,2.01 1.188,2.208 0.313,0.198 10 false 3L 0.885,2.24 1.198,2.438 0.313,0.198 10 false 3K 1.969,1.26 2.281,1.458 0.313,0.198 10 false F15 4.188,0.292 4.5,0.49 0.313,0.198 10 false MB 5.844,1.104 6.156,1.302 0.313,0.198 10 false 3D 5.844,1.76 6.156,1.958 0.313,0.198 10 false 3A 3.604,3.219 3.917,3.417 0.313,0.198 10 false F15 1.5,4.604 1.813,4.802 0.313,0.198 10 false 3H 3.823,4.604 4.135,4.802 0.313,0.198 10 false 3F 5.427,4.604 5.74,4.802 0.313,0.198 10 false 3L 6.396,4.583 6.708,4.781 0.313,0.198 10 false 3K 1.688,6.26 2,6.458 0.313,0.198 10 false 3D 4.917,6.292 5.229,6.49 0.313,0.198 10 false 3A 3.438,7.875 3.75,8.073 0.313,0.198 10 false MB 0.167,0.115 0.531,0.396 0.365,0.281 12 false *A 1.833,0.229 3.021,0.604 1.188,0.375 10 false *1 1.344,2.75 2.531,3.125 1.188,0.375 10 false *a
*A Main Body ECU (Multiplex Network Body ECU) with 1 Connector - -
*1 Main Body ECU (Multiplex Network Body ECU) - -
*a 1 Connector - -


a.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.



b.

Reconnect the instrument panel junction block assembly connectors.


c.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - - Ground Always Below 1 Ω -
MB-31 (BECU) - Body ground Input - Battery power supply (for CPU) Always 11 to 14 V -
F15-6 (FLCY) - Body ground Input R - Body ground Front door courtesy light switch assembly (for LH) input Front door LH closed 10 kΩ or higher FL Door Courtesy SW
Front door LH open Below 1 Ω
F15-27 (FRCY) - Body ground Input BR - Body ground Front door courtesy light switch assembly (for RH) input Front door RH closed 10 kΩ or higher FR Door Courtesy SW
Front door RH open Below 1 Ω
MB-13 (LCTY) - Body ground Input - Rear door courtesy light switch assembly (for LH) input Rear door LH closed 10 kΩ or higher RL Door Courtesy SW
Rear door LH open Below 1 Ω
MB-2 (RCTY) - Body ground Input - Rear door courtesy light switch assembly (for RH) input Rear door RH closed 10 kΩ or higher RR Door Courtesy SW
Rear door RH open Below 1 Ω
MB-4 (BCTY) - Body ground Input - Back door courtesy light switch input Back door closed 10 kΩ or higher Back Door Courtesy SW
Back door open Below 1 Ω


d.

Install the main body ECU (multiplex network body ECU) to instrument panel junction block assembly.



e.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
3D-13 (LSFL) - Body ground Input B - Body ground Front door LH unlock detection switch input Front door LH locked → unlocked Pulse generation
(See waveform 1)
FL Door Lock Pos
3D-12 (LSFR) - Body ground Input GR - Body ground Front door RH unlock detection switch input Front door RH locked → unlocked Pulse generation
(See waveform 1)
FR Door Lock Pos
3D-14 (LSR) - Body ground Input LG - Body ground Rear door LH and Rear door RH unlock detection switch input Rear door LH and Rear door RH locked → Rear door LH or Rear door RH unlocked Pulse generation
(See waveform 1)
RL-Door Lock Pos SW
RR-Door Lock Pos SW
F15-6 (FLCY) - Body ground Input R - Body ground Front door LH courtesy light switch input Front door LH closed → open Pulse generation
(See waveform 2)
FL Door Courtesy SW
F15-27 (FRCY) - Body ground Input BR - Body ground Front door RH courtesy light switch input Front door RH closed → open Pulse generation
(See waveform 2)
FR Door Courtesy SW
3H-24 (LCTY) - Body ground Input BR - Body ground Rear door LH courtesy light switch input Rear door LH closed → open Pulse generation
(See waveform 2)
RL Door Courtesy SW
3A-31 (RCTY) - Body ground Input BR - Body ground Rear door RH courtesy light switch input Rear door RH closed → open Pulse generation
(See waveform 2)
RR Door Courtesy SW
3H-34 (BCTY) - Body ground Input SB - Body ground Back door courtesy light switch input Back door closed → opened Pulse generation
(See waveform 2)
Back Door Courtesy SW
3F-29 (BZR) - Body ground Output L - Body ground Wireless buzzer signal output Procedure:
1.

Engine switch off

2.

All doors closed

3.

Lock switch of electrical key transmitter sub-assembly not pressed → pressed


Below 1 V → pulse generation -


f.
B340769C02
0.219,1.583 0.552,1.75 0.333,0.167 10 false GND 1.25,1.917 1.5,2.083 0.25,0.167 10 false *a 2.219,1.917 2.469,2.083 0.25,0.167 10 false *b
*a Door locked
*b Door unlocked


Using an oscilloscope, check waveform 1.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Tester Connection 3D-13 (LSFL) - Body ground
3D-12 (LSFR) - Body ground
3D-14 (LSR) - Body ground
Tool Setting 2 V/DIV., 200 ms/DIV.
Condition Door locked → unlocked


g.
B340769C03
0.219,1.583 0.552,1.75 0.333,0.167 10 false GND 1.25,1.917 1.5,2.083 0.25,0.167 10 false *a 2.219,1.917 2.469,2.083 0.25,0.167 10 false *b
*a Door closed
*b Door open


Using an oscilloscope, check waveform 2.

NOTICE:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Tester Connection F15-6 (FLCY) - Body ground
F15-27 (FRCY) - Body ground
3H-24 (LCTY) - Body ground
3A-31 (RCTY) - Body ground
3H-34 (BCTY) - Body ground
Tool Setting 2 V/DIV., 200 ms/DIV.
Condition Door closed → opened