Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › 2019.09–2020.08
RM32H0E _58 Vehicle Interior _059623 SEAT _0404458 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B407261

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT ASSEMBLY

a.
B458465

Place the front seat assembly in the vehicle as shown in the illustration.

NOTICE:
·

2 or more people are required when reinstalling the front seat assembly in to the vehicle.

·

Protect the front seat leg.

·

Be careful not to damage the front seat assembly, body exterior or body interior.




b.

Connect the front seat airbag assembly connector under the front seat assembly (w/ Front Seat Side Airbag).

i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B345877C01
3.01,2.594 3.01,2.656 3.01,2.656 3.448,2.656 false 3,1.229 3,1.292 3,1.292 3.438,1.292 false 6.104,0.948 6.104,1.167 6.104,1.167 6.302,1.167 false 6.135,2.375 6.135,2.594 6.135,2.594 6.333,2.594 false 0.969,0.708 1.281,0.906 0.313,0.198 10 false *a 4.448,0.708 4.76,0.906 0.313,0.198 10 false *a 0.969,2.052 1.281,2.25 0.313,0.198 10 false *b 4.458,2.052 4.771,2.25 0.313,0.198 10 false *b 3.521,1.198 3.833,1.396 0.313,0.198 10 false *c 6.375,1.083 6.688,1.281 0.313,0.198 10 false *c 6.396,2.5 6.708,2.698 0.313,0.198 10 false *c 3.51,2.552 3.896,2.698 0.385,0.146 10 false *c
*a Correct *b Incorrect
*c Yellow CPA - -



ii.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

NOTICE:
·

When connecting any airbag connector, take care not to damage the airbag wire harness.


·

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.





c.

Connect each connector and engage each clamp under the front seat assembly.


d.

Temporarily install the front seat assembly with the 4 bolts.


e.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


f.
B453923N01
0.333,0.792 0.49,0.99 0.156,0.198 10 true 1 1.833,1.938 1.99,2.135 0.156,0.198 10 true 2

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



g.

Operate the seat track adjusting handle and move the front seat assembly to the foremost position.


h.
B453922N01
0.333,1.354 0.49,1.552 0.156,0.198 10 true 2 3.146,1.365 3.302,1.563 0.156,0.198 10 true 1

Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration.



Hide 2.INSPECT SEAT SLIDE ADJUSTER LOCK

a.

While performing a sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.


Hide 72158 3.INSTALL INNER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the foremost position.


b.
B453921

Engage the claws and guide to install the inner seat track bracket cover.


Hide 72138 4.INSTALL OUTER SEAT TRACK COVER

a.
B453920

Engage the claws and guide to install the outer seat track cover.


Hide 72128A 5.INSTALL FRONT INNER SEAT TRACK BRACKET COVER

a.

Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.


b.
B453919

Engage the claws to install the front inner seat track bracket cover.


Hide 72124 6.INSTALL FRONT OUTER SEAT TRACK BRACKET COVER

a.
B453918

Engage the claws to install the front outer seat track bracket cover.


Hide 71910A 7.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.

Install the front seat headrest assembly to the front seat assembly.


Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 9.CHECK SEAT HEATER (w/ Seat Heater System)

Hide 10. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Front Seat Side Airbag)

Hide 11.INSPECT SRS WARNING LIGHT (w/ Front Seat Side Airbag)