Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2016.10–2020.08
RM32H0E _58 Vehicle Interior _060065 SEAT BELT _0294235 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B458422E01
2.219,1.948 2.375,2.146 0.156,0.198 10 false 1 2.208,0.771 2.365,0.969 0.156,0.198 10 false 2

Engage the guide and temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 2.INSPECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 73220 3.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.
B458421

Engage the guides to install the front seat outer belt assembly.


b.

Install the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


c.

for TMMT Made:

i.
B459840C01
2.25,0.99 2.594,0.792 true 2.115,0.938 2.427,1.094 0.313,0.156 10 false *a
*a Locking Button


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.




d.

except TMMT Made:

i.
B460474C01
2.198,0.844 2.458,0.656 true 2.042,0.833 2.354,1.031 0.313,0.198 10 false *a
*a Locking Button


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.




e.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


f.

Install the bolt of retractor lower side.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


g.

Check that the ELR locks.

NOTICE:

This check should be performed with the front seat outer belt assembly installed to the vehicle.


i.

With the front seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly.



h.

Remove the bolt of retractor lower side.


Hide 62420A 4.INSTALL CENTER PILLAR GARNISH ASSEMBLY

Hide 62414A 5.INSTALL CENTER PILLAR LOWER GARNISH

Hide 73220 6.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Connect the floor anchor of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73233 7.INSTALL LAP BELT OUTER ANCHOR COVER

a.
B460522C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide and claws to install the lap belt outer anchor cover.


Hide 62332A 8.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

a.

Connect the rear door opening trim weatherstrip.


Hide 67918A 9.INSTALL REAR DOOR SCUFF PLATE

Hide 62312B 10.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Connect the front door opening trim weatherstrip.


Hide 67914 11.INSTALL FRONT DOOR SCUFF PLATE

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION