Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2019.09–2020.08
RM32H0E _58 Vehicle Interior _059856 INTERIOR PANELS / TRIM _0293790 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for LHD and RHD vehicles.

·

The procedure listed below is for the LHD vehicles.



PROCEDURE

Hide 55401E 1.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

Engage the guides to install the instrument panel safety pad sub-assembly as shown in the illustration.

B559142C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)



b.

Engage each clamp.


c.

Connect each connector.


d.

for TMMT Made:

B514921C03
0.104,0.083 2.104,0.833 2,0.75 4.583,3.917 4.75,3.75 true 3.667,3.75 3.833,3.917 true 3.844,1.792 4.177,2.125 true 3.708,4.417 3.958,4.167 true 6.333,1.25 6.667,1.25 true 1.073,0.833 1.073,0.083 false 0.198,0.083 0.521,0.313 0.323,0.229 12 false *A 1.167,0.083 1.51,0.323 0.344,0.24 12 false *B 1.615,2.719 2.396,2.885 0.781,0.167 10 true <B> or <C> 0.604,3.479 0.917,3.646 0.313,0.167 10 true <A> 2.51,3.688 3.344,3.854 0.833,0.167 10 true <B> or <C> 3.208,4.177 3.552,4.344 0.344,0.167 10 true <E> 4.656,4.208 5,4.385 0.344,0.177 10 true <E> 3.469,3.625 3.635,3.792 0.167,0.167 10 true *b 4.792,3.625 4.958,3.792 0.167,0.167 10 true *b 3.667,3.354 4.448,3.521 0.781,0.167 10 true <B> or <C> 5.375,2.917 6.156,3.083 0.781,0.167 10 true <B> or <C> 6.344,3.448 6.656,3.615 0.313,0.167 10 true <A> 4.208,1.625 4.719,1.792 0.51,0.167 10 true <F> *C 6.031,0.792 6.344,0.958 0.313,0.167 10 true <F> 3.625,1.677 3.792,1.844 0.167,0.167 10 true *d 6.74,1.146 6.906,1.313 0.167,0.167 10 false *c 3.49,4.333 3.656,4.5 0.167,0.167 10 true *a
*A for Type A *B for Type B
*C w/o Radio Receiver - -
*a Airbag Connector *b Airbag Bolt
*c Ground Bolt A *d Ground Bolt B


i.

Connect the airbag connector.


ii.

Install the 4 clips.


iii.

Install the 2 airbag bolts as shown in the illustration.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


iv.

Install the ground bolt A as shown in the illustration.

Torque:
for Type A : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


v.

w/o Radio Receiver:

1.

Install the ground bolt B as shown in the illustration.


Torque:
for Type A : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)


vi.

Install the 6 bolts as shown in the illustration.



e.

except TMMT Made:

B558574C01
2.302,3.344 2.531,3.219 true 3.479,3.406 3.281,3.313 true 6.76,0.594 6.344,0.385 true 3.188,3.552 3.063,3.375 true 0.635,2.74 0.938,2.896 0.302,0.156 10 true <A> 6.406,2.448 6.708,2.604 0.302,0.156 10 true <A> 2.51,2.833 2.813,2.99 0.302,0.156 10 true <E> 3.365,2.906 3.667,3.063 0.302,0.156 10 true <E> 3.875,2.813 5.125,2.99 1.25,0.177 10 true <B> or <C> 2.5,2.563 3.292,2.75 0.792,0.188 10 true <B> or <C> 0.969,2.167 1.781,2.354 0.813,0.188 10 true <B> or <C> 4.813,1.74 5.615,1.927 0.802,0.188 10 true <B> or <C> 6.344,0.073 6.646,0.229 0.302,0.156 10 true <F> 6.802,0.563 7.042,0.75 0.24,0.188 10 true *c 2.156,3.333 2.396,3.521 0.24,0.188 10 true *b 3.49,3.333 3.677,3.531 0.188,0.198 10 true *b 3.135,3.552 3.344,3.74 0.208,0.188 10 true *a
*a Airbag Connector *b Airbag Bolt
*c Ground Bolt - -


i.

Connect the airbag connector.


ii.

Install the 4 clips.


iii.

Install the 9 bolts as shown in the illustration.

Torque:
Airbag bolt : 20 N*m (204 kgf*cm, 15 ft.*lbf)
Ground bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 55085 2.INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY

a.
B459245C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the No. 2 heater to register duct sub-assembly as shown in the illustration.


Hide 55011A 3.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/ Display)

a.
B512686C01
0.906,1.521 0.75,1.292 false 0.906,1.552 1.219,1.708 0.313,0.156 10 false *a 0.469,1.802 0.781,1.958 0.313,0.156 10 false *b 1.49,1.563 1.802,1.719 0.313,0.156 10 false *b
*a Runner Portion
*b Cut Off


When installing a new No. 1 instrument panel garnish sub-assembly:

i.

Using a nipper, cut off both ends of the runner portion as shown in the illustration.



b.
B512685C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips and guides to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.


c.

Install the 2 bolts <A>.


Hide 86140A 4.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)

Hide 55670A 5.INSTALL INSTRUMENT PANEL CENTER REGISTER ASSEMBLY

a.
B478036C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and claws to install the instrument panel center register assembly as shown in the illustration.


b.

Install the 2 screws <D>.


Hide 55011A 6.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/o Display)

a.
B467659C01
1.115,1.24 0.938,1.083 false 1.167,1.25 1.479,1.406 0.313,0.156 10 false *a 0.625,1.729 0.938,1.885 0.313,0.156 10 false *b 1.469,1.448 1.781,1.604 0.313,0.156 10 false *b
*a Runner Portion
*b Cut Off


When installing a new No. 1 instrument panel garnish sub-assembly:

i.

Using a nipper, cut off both ends of the runner portion as shown in the illustration.



b.
B459243C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and clips to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.


Hide 55414C 7.INSTALL STARTER SWITCH BEZEL (for LHD with Entry and Start System)

a.

Connect the connector.


b.
B459239C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the starter switch bezel as shown in the illustration.


Hide 55406B 8.INSTALL INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY

a.

Connect the connector.


b.
B459237C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the instrument cluster finish lower center panel sub-assembly as shown in the illustration.


Hide 86211 9.INSTALL NO. 1 RADIO BRACKET (w/o Cover)

a.
B459234

Engage the guides to install the No. 1 radio bracket.


b.

Install the 2 bolts <A>.


Hide 86212 10.INSTALL NO. 2 RADIO BRACKET (w/o Cover)

a.
B459235

Engage the guides to install the No. 2 radio bracket.


b.

Install the 2 bolts <A>.


Hide 86211 11.INSTALL NO. 1 RADIO BRACKET (w/ Cover)

a.
B459232

Engage the guides to install the No. 1 radio bracket.


b.

Install the 3 screws <D>.


Hide 86212 12.INSTALL NO. 2 RADIO BRACKET (w/ Cover)

a.
B459233

Engage the guides to install the No. 2 radio bracket.


b.

Install the 3 screws <D>.


Hide 55521C 13.INSTALL STEREO OPENING COVER WITH BRACKET (w/ Cover)

a.

Connect the connector.


b.
B459231

Engage the guides to install the stereo opening cover with bracket.


c.

Install the 4 bolts <A>.


Hide 86120 14.INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)

Hide 55405B 15.INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY (w/o Display)

a.
B459230C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the instrument cluster finish center panel sub-assembly as shown in the illustration.


Hide 55045 16.INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

a.
B459226

Engage the clips to install the instrument panel lower finish panel sub-assembly to the fuse box opening cover.


b.

Install the 2 screws <D>.


Hide 55545 17.INSTALL FUSE BOX OPENING COVER (w/o Knee Airbag)

a.

Connect each connector.


b.
B459225C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips and claws to install the fuse box opening cover with instrument panel lower finish panel sub-assembly as shown in the illustration.


c.

Install the screw <D>.


Hide 73997 18.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR (w/ Knee Airbag)

Hide 55545 19.INSTALL FUSE BOX OPENING COVER (w/ Knee Airbag)

a.

Connect each connector.


b.
B459223C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the fuse box opening cover as shown in the illustration.


c.

Install the screw <D>.


Hide 53601 20.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B459221C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and claw to connect the hood lock control lever sub-assembly as shown in the illustration.


Hide 83100 21.INSTALL COMBINATION METER ASSEMBLY

Hide 55414C 22.INSTALL STARTER SWITCH BEZEL (for RHD with Entry and Start System)

a.

Connect the connector.


b.
B459219C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the starter switch bezel as shown in the illustration.


Hide 55012A 23.INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.
B459217C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the No. 2 instrument panel garnish sub-assembly as shown in the illustration.


Hide 55410C 24.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B459215C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides and clips to install the instrument cluster finish panel assembly as shown in the illustration.


b.

Install the 2 clips.


c.
B459213C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the meter hood spacer as shown in the illustration.


Hide 55404D 25.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

w/ Switch:

i.

Connect each connector.



b.
B459211C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the instrument cluster finish panel sub-assembly as shown in the illustration.


Hide 86160P 26.INSTALL NO. 2 FRONT SPEAKER ASSEMBLY (w/ Woofer)

Hide 55408F 27.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.

w/ Speaker:

i.

Connect the connector.



b.
B459209C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides, claws and clips to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.


Hide 55409F 28.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

HINT:

Use the same procedure as for the No. 1 instrument panel speaker panel sub-assembly side.


Hide 62212 29.INSTALL FRONT PILLAR GARNISH LH

a.
B459207C02
0.76,1.302 1.292,1.115 true 0.51,1.271 0.729,1.5 0.219,0.229 10 true *a
*a Protective Cover
V100155

Adhesive Tape


Remove the adhesive tape and protective cover.


b.
B459249

Install the 2 front pillar garnish clips to the front pillar garnish LH.

NOTICE:
·

If the front pillar garnish clip has significant damage, replace it with a new one.

·

When installing the front pillar garnish clip, make sure to install it in the correct position and facing in the correct direction.




c.

w/ Speaker:

i.

Connect the connector.



d.
B459205C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides as shown in the illustration.


e.
B459206C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips to install the front pillar garnish LH as shown in the illustration.


Hide 62211 30.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 55318C 31.INSTALL INSTRUMENT SIDE PANEL LH

a.
B459201C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides and clips to install the instrument side panel LH as shown in the illustration.


b.

w/ Airbag Cut Off Switch:

i.

Connect the connector.



Hide 55317A 32.INSTALL INSTRUMENT SIDE PANEL RH

HINT:

Use the same procedure as for the LH side.


Hide 55436A 33.INSTALL INSTRUMENT PANEL FINISH END PANEL LH

a.
B459199C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides and clips to install the instrument panel finish end panel LH as shown in the illustration.


Hide 55435A 34.INSTALL INSTRUMENT PANEL FINISH END PANEL RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 35.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B461389

Connect the front door opening trim weatherstrip LH to the area shown in the illustration.


Hide 62311B 36.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 55433B 37.INSTALL NO. 2 INSTRUMENT PANEL LOWER FINISH PANEL

a.

Connect the connector.


b.
B459197C01
0,0 0,0 false
V113147

Install in this Direction


Engage the clips and claws to install the No. 2 instrument panel lower finish panel as shown in the illustration.


c.

Install the 5 screws <D>.


Hide 55054 38.INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY

a.
B459195

Engage the claw to install the glove compartment door stopper sub-assembly.


Hide 55550 39.INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

a.
B459194C01
0,0 0,0 false
V113147

Install in this Direction


With the glove compartment door assembly opened approximately 61° from its closed position, engage the 4 hinges horizontally.

NOTICE:
·

Engaging the hinges from the top will deform the hinges.

·

Be sure to install the glove compartment door assembly horizontally.




b.
B459192C02
0.635,0.906 0.458,0.521 true 2.625,0.76 2.823,0.427 true 2.833,0.323 3.042,0.49 0.208,0.167 10 true *a 0.24,0.438 0.448,0.604 0.208,0.167 10 true *a
*a Stopper


While pushing in the sides of the glove compartment door assembly as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.


c.
B459191

Engage the claw to connect the glove compartment door stopper sub-assembly.


Hide 55607 40.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B459257C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the guides and claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.


Hide 62111C 41.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION


Hide 67913 42.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION


Hide 84140 43.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 44.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 45.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION