88460
1.INSTALL COOLER CONDENSER ASSEMBLY
|
Install in this Direction |
Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.
Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.
If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.
Add 40 cc (1.35 fl. oz)
for VALEO Made
VC100YF or equivalent
for DENSO Made
ND-OIL 8 or equivalent
88716A
2.CONNECT COOLER REFRIGERANT LIQUID PIPE A (for VALEO Made)
Remove the vinyl tape from the cooler refrigerant liquid pipe A and cooler condenser assembly.
Apply sufficient compressor oil to a new O-rings and fitting surfaces of the cooler refrigerant liquid pipe A
VC100YF or equivalent
Install the O-ring to the air cooler refrigerant liquid pipe A.
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
Connect the cooler refrigerant liquid pipe A to the cooler condenser assembly with the bolt.
88716A
3.CONNECT COOLER REFRIGERANT LIQUID PIPE A (for DENSO Made)
Remove the vinyl tape from the open ends of the cooler condenser assembly and cooler refrigerant liquid pipe A.
| *1 | Air Conditioner Tube and Accessory Assembly |
| *2 | Piping Clamp |
| *a | Groove |
Install a new piping clamp to the cooler refrigerant liquid pipe A.
Securely engage the inside step of the piping clamp in the cooler refrigerant liquid pipe A groove.
Do not widen the opening of the piping clamp more than the diameter of the cooler refrigerant liquid pipe A when installing it.
Do not install the piping clamp with the large diameter section in the wrong direction.
Thoroughly coat 2 new O-rings and the contact surface of the cooler refrigerant liquid pipe A with compressor oil.
ND-OIL 8 or equivalent
Install the 2 O-rings to the cooler refrigerant liquid pipe A.
Do not let foreign matter adhere to the O-rings or O-ring seals.
Engage the cooler condenser assembly and cooler refrigerant liquid pipe A.
| *a | Large Diameter Section of Piping Clamp | - | - |
Engage the parts by holding the pipe, not the piping clamp.
Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.
When inserting, make sure that a click sound is heard.
Check that the cooler refrigerant liquid pipe A is securely inserted by pulling it.
88703
4.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
Remove the vinyl tape from the discharge hose sub-assembly and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.
for VALEO Made
VC100YF or equivalent
for DENSO Made
ND-OIL 8 or equivalent
Install the O-ring to the discharge hose sub-assembly.
Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.
16595B
5.INSTALL NO. 1 RADIATOR AIR GUIDE LH
16593B
6.INSTALL NO. 1 RADIATOR AIR GUIDE RH
52131A
7.INSTALL FRONT BUMPER REINFORCEMENT
52611
8.INSTALL FRONT BUMPER ENERGY ABSORBER
16594
9.INSTALL NO. 2 RADIATOR AIR GUIDE (for 8NR-FTS)
16594
10.INSTALL NO. 2 RADIATOR AIR GUIDE (for 3ZR-FAE)
53205
11.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 8NR-FTS)
53205
12.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 3ZR-FAE)
53510
13.INSTALL HOOD LOCK ASSEMBLY
w/ Engine Hood Courtesy Switch:
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSTALLATION
w/o Engine Hood Courtesy Switch:
Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY>INSTALLATION
53579
14.INSTALL HOOD LOCK NUT CAP
16561C
15.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
53117C
16.INSTALL NO. 1 RADIATOR GRILLE RETAINER
52029A
17.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY (for 8NR-FTS)
52029A
18.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY (for 3ZR-FAE)
17751
19.INSTALL NO. 1 AIR CLEANER INLET (for 8NR-FTS)
17751
20.INSTALL NO. 1 AIR CLEANER INLET (for 3ZR-FAE)
21.INSTALL HEADLIGHT ASSEMBLY LH (for Single Beam Headlight)
22.INSTALL HEADLIGHT ASSEMBLY RH (for Single Beam Headlight)
Use the same procedure as for the LH side.
23.INSTALL HEADLIGHT ASSEMBLY LH (for Triple Beam Headlight)
24.INSTALL HEADLIGHT ASSEMBLY RH (for Triple Beam Headlight)
Use the same procedure as for the LH side.
25.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))
26.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))
27.WARM UP WARM UP ENGINE (for HFC-134a(R134a))
28.WARM UP WARM UP ENGINE (for HFO-1234yf(R1234yf))
29.INSPECT FOR REFRIGERANT LEAK (for HFC-134a(R134a))
30.INSPECT FOR REFRIGERANT LEAK (for HFO-1234yf(R1234yf))
53510
31.ADJUST HOOD LOCK ASSEMBLY