1.INSTALL RADIATOR DRAIN COCK PLUG
Install the O-ring to the radiator drain cock plug.
Replace the O-ring if it is damaged.
Install the radiator drain cock plug.
16533C
2.INSTALL RADIATOR SUPPORT GROMMET
Install the 2 radiator support grommets to the radiator assembly.
16523A
3.INSTALL RADIATOR SUPPORT CUSHION
Install the 2 radiator support cushions to the radiator assembly.
16400
4.INSTALL RADIATOR ASSEMBLY
Engage the 2 guides.
Engage the 2 claws to install the fan shroud assembly to the radiator assembly.
Do not damage the radiator assembly when installing the fan shroud assembly.
Install the radiator assembly together with the fan shroud assembly to the vehicle.
88460
5.INSTALL COOLER CONDENSER ASSEMBLY
88716A
6.CONNECT COOLER REFRIGERANT LIQUID PIPE A
88703
7.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
16595B
8.INSTALL NO. 1 RADIATOR AIR GUIDE LH
16593B
9.INSTALL NO. 1 RADIATOR AIR GUIDE RH
52131A
10.INSTALL FRONT BUMPER REINFORCEMENT
52611
11.INSTALL FRONT BUMPER ENERGY ABSORBER
16572D
12.CONNECT NO. 2 RADIATOR HOSE
Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.
Engage the clamp to the fan shroud.
16573B
13.CONNECT NO. 3 RADIATOR HOSE
Connect the No. 3 radiator hose to the radiator assembly and slide the clip to secure it.
16267
14.CONNECT NO. 3 WATER BY-PASS HOSE
Connect the No. 3 water by-pass hose to the radiator assembly and slide the clip to secure it.
Engage the 4 clamps to the fan shroud.
16261
15.CONNECT NO. 1 WATER BY-PASS HOSE
Connect the No. 1 water by-pass hose to the radiator assembly and slide the clip to secure it.
16577C
16.CONNECT RADIATOR PIPE
Connect the radiator pipe to the fan shroud, and then install the 2 bolts.
16594
17.INSTALL NO. 2 RADIATOR AIR GUIDE
Engage the 4 claws to install the No. 2 radiator air guide to the radiator assembly.
53205
18.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Install the upper radiator support sub-assembly together with the hood lock support sub-assembly to the vehicle with the 5 bolts.
Engage the clamp to connect the wire harnesses to the cooling fan ECU and fan shroud.
Engage the 3 clamps to connect the wire harness to the horn and hood lock support assembly.
Engage the clamp to connect the hood control cable sub-assembly to the upper radiator support sub-assembly.
53510
19.INSTALL HOOD LOCK ASSEMBLY
w/ Engine Hood Courtesy Switch:
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSTALLATION
w/o Engine Hood Courtesy Switch:
Click hereVehicle Exterior>DOOR / HATCH>HOOD LOCK CONTROL CABLE ASSEMBLY>INSTALLATION
20.INSTALL HOOD LOCK NUT CAP
16561C
21.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL
53117C
22.INSTALL NO. 1 RADIATOR GRILLE RETAINER
52021B
23.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Install the front bumper upper reinforcement sub-assembly to the vehicle with the 4 bolts.
17751
24.INSTALL NO. 1 AIR CLEANER INLET
Install the No. 1 air cleaner inlet to the upper radiator support sub-assembly and air cleaner case sub-assembly with the 4 bolts.
25.INSTALL HEADLIGHT ASSEMBLY LH
for Triple Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Triple Beam Headlight)>INSTALLATION
for Single Beam Headlight:
Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Single Beam Headlight)>INSTALLATION
26.INSTALL HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
27.ADD ENGINE COOLANT
28. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
29.INSPECT FOR COOLANT LEAK
51441
30.INSTALL NO. 1 ENGINE UNDER COVER
31. WARM UP ENGINE
32.INSPECT FOR REFRIGERANT LEAK