The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the windshield glass removal/installation are shown below.
When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane departure alert system, pre-crash safety system, forward recognition camera system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
75534
1.REMOVE WINDSHIELD OUTSIDE MOULDING LH
75533
2.REMOVE WINDSHIELD OUTSIDE MOULDING RH
Use the same procedure as for the LH side.
85292B
3.REMOVE FRONT WIPER ARM HEAD CAP
85221B
4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
85211B
5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
55708
6.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
87810
7.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
87810
8.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
89941
9.REMOVE RAIN SENSOR (w/ Rain Sensor)
8646C
10.REMOVE FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
81260A
11.REMOVE MAP LIGHT ASSEMBLY (for TMMT Made)
81260A
12.REMOVE MAP LIGHT ASSEMBLY (for TMC Made)
81340
13.REMOVE VANITY LIGHT ASSEMBLY
62312B
14.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62311B
15.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Use the same procedure as for the LH side.
62212
16.REMOVE FRONT PILLAR GARNISH LH
62211
17.REMOVE FRONT PILLAR GARNISH RH
Use the same procedure as for the LH side.
74612
18.REMOVE ASSIST GRIP COVER
74610A
19.REMOVE ASSIST GRIP SUB-ASSEMBLY
74325
20.REMOVE VISOR BRACKET COVER
74320
21.REMOVE VISOR ASSEMBLY LH (w/ Vanity Light)
74310
22.REMOVE VISOR ASSEMBLY RH (w/ Vanity Light)
Use the same procedure as for the LH side.
74320
23.REMOVE VISOR ASSEMBLY LH (w/o Vanity Light)
74310
24.REMOVE VISOR ASSEMBLY RH (w/o Vanity Light)
Use the same procedure as for the LH side.
74348
25.REMOVE VISOR HOLDER
63311C
26.SEPARATE ROOF HEADLINING
Slightly lower the front section of the roof headlining so that the windshield glass can be removed.
Do not damage the roof headlining or vehicle interior.
It is not necessary to completely remove the roof headlining.
56111
27.REMOVE WINDSHIELD GLASS
w/ Windshield Deicer System:
Disconnect the connector.
|
Protective Tape |
Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.
| *1 | Windshield Glass |
| *2 | Windshield Outside Moulding |
| *a | Cut |
Using a knife, cut off the windshield outside moulding as shown in the illustration.
| *a | Matchmark |
Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.
Matchmarks are not necessary if the windshield glass is not going to be reused.
| *1 | Windshield Glass Stopper |
| *2 | Front Window Inner Center Moulding |
| *a | Piano Wire |
Pass a piano wire between the vehicle body and windshield glass from the interior.
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut the adhesive by pulling the piano wire around the windshield glass.
When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
To prevent the instrument panel safety pad sub-assembly from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and instrument panel safety pad sub-assembly.
Do not damage the front window inner center moulding.
Disengage the windshield glass stoppers.
| *A | for 1-piece Type | *B | for 2-piece Type |
| *1 | No. 1 Windshield Glass Stopper | *2 | No. 2 Windshield Glass Stopper |
The No. 1 windshield glass stoppers and No. 2 windshield glass stoppers are installed to the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting the adhesive.
To prevent the windshield glass rom falling when performing this operation, be sure to hold the windshield glass using suction cups.
Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.
Using suction cups, remove the windshield glass.
Be careful not to drop the windshield glass.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass.
56117A
28.REMOVE WINDOW GLASS ADHESIVE DAM
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the window glass adhesive dam.
Be careful not to damage the windshield glass.
Be sure to replace the window glass adhesive dam with a new one.
75533G
29.REMOVE WINDSHIELD OUTSIDE MOULDING
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the windshield outside moulding.
Be careful not to damage the windshield glass.
Be sure to replace the windshield outside moulding with a new one.
56115A
30.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
Be careful not to damage the windshield glass.
Be sure to replace the 1-piece type No. 1 windshield glass stoppers with new 2-piece type No. 1 and No. 2 windshield glass stoppers.
56116C
31.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
When reusing the windshield glass:
| *a | Back Side of Windshield Glass |
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
Be careful not to damage the windshield glass.
Be sure to replace the No. 2 windshield glass stoppers with new ones.
56115A
32.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 windshield glass stoppers from the vehicle body.
Be sure to replace the No. 1 windshield glass stoppers with new ones.
56153C
33.REMOVE FRONT WINDOW INNER CENTER MOULDING
Perform the following procedure only when replacement of a front window inner center moulding is necessary.
| *a | Back Side of Windshield Glass |
| *b | Matchmark |
Place matchmarks on the windshield glass at the locations indicated in the illustration.
Using a scraper, remove the front window inner center moulding.
Be careful not to damage the windshield glass.
Be sure to replace the front window inner center moulding with a new one.